Models > EKT-396 > Instructions

EKT-396 Caloric Microwave Oven Combo - Instructions

All Instructions for the EKT-396
31 - 45 of 116
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Screw hard to get off
Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.
Parts Used:
Surface Burner Plug-In Block Kit
  • Lawrence from BROOKSVILLE, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
Parts Used:
Ceramic Fuse - 20 amp
  • Richard from CALIFORNIA, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The broil element had burnt into,
Remove three strews and two wires. Less than fifteen minutes for this Seventy Seven year old farm boy!
Parts Used:
Broil Element - 240V
  • Don from Hazlehurst, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing oven rack
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Parts Used:
Wire Oven Rack
  • Denise from Pittsburgh, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner inop
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair
Parts Used:
Surface Burner Plug-In Block Kit
  • Donald from Milford, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fuse blows when start cooking.
Replace the capacitor and the fuse. Then it works again. Part arrived in an open plastic bag with scratch. It looked like a returned part, but it works fine.
Parts Used:
CAPACITOR
  • Phuong from plano, TX
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Maytag Microwave UMC5100AD fixes
My Maytag Microwave UMC5100AD was suddenly broken in 1 second when I heated food last time. Then no clock, etc, seem the fuse broken. to fix it, the most difficult part was how to remove it from the wall trim. Finally got it out. Then went HomeDepot to get the same fuse, replaced and used it, burned again. Then I searched online and ppl said the capacitor might be the one. I took it out and measured it, yeah it indeed was a problem since it's not open. Then I order the capacitor from PartSelect about $32. After 3 days I got it and installed it. Done. Sure need to put the Microwave back to wall trim. That's it. Saved about $500 buck if I buy a new one plus labor to install it. Thanks
Parts Used:
CAPACITOR
  • Biao from Houston, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The heating element on the left front burner was out
Pulled the old one out and plugged the new one in. It was that simple!
Parts Used:
Range Surface Element
  • Julie from Salt Lake City, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
N/A
I followed the instructions provided.
Parts Used:
Surface Burner Plug-In Block Kit
  • Gerry from Mackay, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Nicki from ELSIE, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Sandra Collignon from SANTA CLAUS, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The three braces under the coils had weakened and fallen apart
I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.
Parts Used:
Surface Element - 6 Inch
  • Suzanne from COZAD, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove Burner wouldn't heat up
Someone did the repair for me.
Parts Used:
Surface Burner Plug-In Block Kit
  • Donna from Sandwich, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing An Oven Rack Due To Plastic Fire In Our Oven. Plastic Melted Onto The Rack...Instead Of Taking The Time To Melt The Rest Off, My Husband Threw It Away =(
Bought a new one. . Three years later =)
Parts Used:
Wire Oven Rack
  • Nicole from Rogers, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Michael from Portland, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the EKT-396
31 - 45 of 116
Back to Top