Models
>
EI30GF45QSC
EI30GF45QSC Electrolux Range - Overview
Sections of the EI30GF45QSC
[Viewing 7 of 7]Manuals & Care Guides for EI30GF45QSC
Click to downloadInstall
Installation Instructions
(1.87MB)
Specs
Product Specifications Sheet
(0.62MB)
Wiring
Wiring Diagram
(0.62MB)
Keep searches simple, eg. "belt" or "pump".
LP Conversion Kit
PartSelect #: PS3633782
Manufacturer #: GRLP4
The LP conversion kit is used in ranges
$78.59
In Stock
CAP
PartSelect #: PS11775705
Manufacturer #: 5304508442
The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner...
$24.35
In Stock
CAP
PartSelect #: PS11775704
Manufacturer #: 5304508441
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
$30.07
In Stock
Igniter/Orifice Mounting Screw
PartSelect #: PS440022
Manufacturer #: 316240600
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
$12.23
In Stock
CAP
PartSelect #: PS11775706
Manufacturer #: 5304508443
This black burner cap is a genuine OEM part made of a durable material capable of reaching 14,000-BTU, with an approximately 3-inch diameter. It is compatible with various models of ranges and cooktop...
$35.49
In Stock
Outer Drawer Glide
PartSelect #: PS977459
Manufacturer #: 316105501
As per the factory, the original part was 19 3/4 inches and the new substituted part is 16 1/4 inches. According to the factory, this part will still work with your appliance.
$71.84
In Stock
Questions And Answers for EI30GF45QSC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the EI30GF45QSC
[Viewing 6 of 6]Oven is too hot
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O
... Read more
nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Read less
Parts Used:
-
John from Stevensville, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
16 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top oven overheating
Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
Parts Used:
-
Ronald from NEVADA, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner indicator light lense broke off
The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will
... Read more
hold it in place.
Read less
Parts Used:
-
Kathy from NEW BERN, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!