EER3002H00CC General Electric Range - Instructions

Went to the rear of stove took off bolts attach, slipped the old element out and inserted the new one then re-attached the bolts.

So ordered my racks and used them right away--nothing to it--it is oven racks! But your service was so prompt and description thorough enough to figure it all out and get it ordered.thanks

Repair was easy. 1. Turn off the electric to range. 2. very carefully remove the door(makes it real easy to access inside the oven.) 3. remove the 2 screws but be careful. 4. remove the two push on teminals. 5. The wires are very very short so they snapped back into the back of unit. 6. pulled out range and took off the 5 screws holding the small metal piece protecting all electrical wires...7. found the two terminal wires and push them on new terminal leads. 8. screwed the elements two screws back in, 9. replaced the small back with the 5 screws. 10. cleaned the floor behind the range and pushed it back in place.... DONE.... element works fine...tested it. however not cooking with oven today with temps outside at 104-105 ...will wait till it gets a little cooler... but all in all it was a piece of cake.....

Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again

When I removed the unit I failed to secure the clip on wires - AND zing they went back into the insulation - now it required pulling unit out removing the back panel and placing wires thru the insulation and back into the oven - job was then very simple

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Parts Select delivered my item quickly and in good condition. The replacement of the baking element was very easy. The following seven steps took less than 10 minutes to complete: 1) Pull the stove from the wall and unplug the oven (This was a great opportunity to ensure the floor area was clean and free from food particles) 2) Use Pliers to remove the back panel covering 3)unhook the bake element from the wire connections 4) Remove the bake element and replace with new one 5) reconnect new element prongs to wires 6) Replace back panel 7) Plug stove into the wall and push stove back to wall. Now I am ready just in time for the holiday baking season.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed oven back plate. Pluged oven in. Works great.

I called my dad and he came right over and fixed it. He is a super dad!

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Followed the instructions that were sent to me by E-Mail.

a) Turn off 240v ckt brkr to the oven p b) In the Rear -Remove the 6 hex screws holding the protective covering c) Remove the two push-on terminals p d) In front, open door to range and remove the two screws holding the faulty bake element p e) Remove faulty bake element and replace with new one f) Replace all screws p