EER3002H00CC General Electric Range - Instructions

removed old element--had read warnings about wiring would go back into insulation--pliers slipped and one wire "jumped" back into insulation--had to take back off stove to retrieve the connection--other than that incident, the connection was simple--suggestion--make sure you have needle nosed vise grip pliers to prevent wire from becoming lost in the insulation---could not find my pliers so had to use regular pliers.

Removed old lower bake element on the inside by removing nuts at the back of inside of stove which holds element in place. Then removed metal guard panel on the outside back of stove to disconnect old terminals. Then from the inside of oven removed the old element and reconnected the new element terminals.

Easy to install replacement parts using the screws provided.

Unplugged the old and plugged the new one. replaced the covers and turned the power back on. No problems!!

I found that installing my element was far easier when I found this link it is a video on how to install this part It made it far easier to install correctly.

turned power off, loosing the to screws, left up and pull front, removed the two connection.placed new element inside oven fsten the two wires. push elemen, back in place, allaing screw holes tighten screw, turn power back on. Stove(oveb) working just like new.

Simple; unplug stove, take back cover plate off. Pull off front knob. Remove screws holding in switch.Replace wires one at a time to avoid dis-connections - or make color coded diagram. put back together. DONE

Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

Parts fit perfect, and order them on Wednesday and they were delivered on Friday morning. Excellent service. Thank you. Happy customer.

Unscrew the two nuts in the back of oven holding the bake element,carefully secure the electrical connections with plyers so they won't go back into the stove. Slowly, pull the bake element out of the electrical sockets, one at the time. Next insert the electrical parts into the new element ends, screw back the nuts, and done!

It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.

Removed the two racks, remove two screws from the back of heat element, carefully pull element out, unplugs wires from element, install new element in the reverse order

Moved the stove away from the wall and unplugged. Removed screws from the back of the stove. Took out old element and replaced with new. Replaced the screws, plugged the stove back in and turned on the oven to make sure everything was working. Everything working fine and I baked a cake. I was also very happy how quickly I received the part. I ordered it late Thursday afternoon and received it by the following Saturday morning. Thank you.

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

ordered it and it was here within 48 hours. I was so surprised to see it so quicly. It took me just a few minutes to put it n and tighten it up and all is well now. Piece of cake!