EER3000H01BB General Electric Range - Instructions

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.

Installation instructions on the partsdirect site were great. Unscrewed the (2) hex head screws that hold the element and used clamps to hold the terminal ends from recoiling back into the insulation of the oven cabinet. Put the push on terminal ends on the new element, tightened screws and done. The $50. Part fixed the problem and delayed another range purchase.

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

Pull knob. Pull wires. Pull two screws. Replace switch

We emptied the bottom drawer and pulled out the stove, unplugged it and my wonderful son came over and installed the part in about 15 - 20 minutes. The part came without instructions, so we were glad he was around. I am glad we were able to find your service. Thanks.

After reading on the website of others doing repairs I was able to fix my oven easily. I removed the two screws on the back wall of the oven. I carefully pulled the element forward bringing with it the connector wires. Before sliding them off of the old element I made sure that they were pulled out far enough so not to loose them in the insulation. I removed the old element. Slid the connector wires on to the element. Carefully slid the element back into the back of the oven. Put the screws back in and I was done.

I ordered new oven racks. My old ones were the original with the range (uncleanable). I cleaned by oven till it shined and when I put in the new racks it looked like a new oven. I'm very happy.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

First I turned off the breaker to the oven, then removed the oven racks. I removed the two small bolts that hold the element to the back wall of the oven. I then gently pulled the element out to expose the terminals, with needle nose pliers I carefully removed the clips without letting the wires slip back behind the oven wall. Then I pushed the clips onto the new element and bolted it back onto the oven wall. I turned the breaker back on and preheated the oven and it worked like a charm.

The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.

took the old ones out & put the new ones in. Piece of cake!!Thanks for the prompt delivery!!

Turned circuit breaker off to range as recommneded. Removed 2 screws from old heating element using a nut driver after removing the two racks from inside the oven. Considereing others had noted the wire sometimes came off and had to be retrieved by removing the back panel, I removed the back panel using the nut driver instead of waiting to see if that would happen. I removed the back panel after sliding the range out for easy access. Back panel was removed using the nut driver on approximately five screws that secured the back panel. This step may not have been needed because the wires were secured snug on the heating element. Secured new heating element and back panel. Turned on power after tripping circuit breaker and noticed a bright red hearting element in range within one minute. Real simple repair quickly done minutes after delivery by UPS.

We pulled the stove out, unplugged it, unscrewed the old element and screwed the new one in.

pull gasket from door bottom and pull gasket to release retainers in door frame. refit new seal in retainer holes and push gasket into slots at bottom of door. done perfect fit.

Extremely easy, two screws pull connection inward to oven grasp push pin pull disconnect (don't let go of oven end or it will recede into appliance) push pin new connection on two connections. Remount with two screws and job was done! And yes a woman repaired her own oven very easy!