EER2002M02BS General Electric Range - Instructions

I ordered it online and it came to our house in less than 24 hours which is very impressive since we live in a very remote place. There were responses from other people who had the same problem and what they had to do to fix it which was very helpful because we knew what might happen. The wires went into the back of the oven when the old element was removed. We were ready, opened up the back of the oven and stuck it back in, connected it, cleaned behind the oven while it was out, put it back, and it works like new. Thankyou so much!

Went to the rear of stove took off bolts attach, slipped the old element out and inserted the new one then re-attached the bolts.

Repair was easy. 1. Turn off the electric to range. 2. very carefully remove the door(makes it real easy to access inside the oven.) 3. remove the 2 screws but be careful. 4. remove the two push on teminals. 5. The wires are very very short so they snapped back into the back of unit. 6. pulled out range and took off the 5 screws holding the small metal piece protecting all electrical wires...7. found the two terminal wires and push them on new terminal leads. 8. screwed the elements two screws back in, 9. replaced the small back with the 5 screws. 10. cleaned the floor behind the range and pushed it back in place.... DONE.... element works fine...tested it. however not cooking with oven today with temps outside at 104-105 ...will wait till it gets a little cooler... but all in all it was a piece of cake.....

Very easy to fix with two people and works great

Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again

When I removed the unit I failed to secure the clip on wires - AND zing they went back into the insulation - now it required pulling unit out removing the back panel and placing wires thru the insulation and back into the oven - job was then very simple

Per the instructions... I just wish I had read them first... It took me 10 min longer but it all turned out right and a LOT cheaper than calling the repair man.

remove two bolts in on sensor and slip thru back un plug and reverse to put in

after reading instructions on this site , i knew to take the 2 screws out of the element in the rear of the oven. As soon as i saw the wires i put the clamps on them so they wouldn't fall back into the wall of the oven, then i just pulled off the old element and pushed on the new. Put screws in with nut driver and turned power back on.

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

Repairs went well. By the way you guys rock! From the easiness of your website to receiving the part a day ahead of schedule! We are baking again.

Very simple fix, after unplugging the range to shut off power, there were two screws to remove on the inside of the oven, and also removed the panel from the back with only four short screws.. the fix was simple and cost a lot less than what I would have paid to purchase a new range... The part arrived shortly after the order was placed...

Remove one screw replace element and return the screw.