EDW6100N00WW General Electric Dishwasher - Instructions

Remove bottom articulating sprayer and water fittings. Remove and replace filter

just snapped the new part in. couldn't have been easier

I ordered both new wheels and stud that goes in the centers of each wheel. It took longer to cut the bags open than to install them. Works like a dream and no sqeaking and dishwasher works better since it is the correct distance from the water rotation arm on the bottom of the washer! Wonderful experience by an all thumbs do it yourselfer!

After finally getting the door open and opening it up, the problem became apparent. Partselect helped me locate the part. it came quickly, and the repair was simple. It took me two trys to discover how the spring fit, but once I looked closely at the diagram, it was a cinch. I was a very proud dishwasher owner!

I used needle nose pliers. I bent the stainless steel guide arm out so that I could insert the end cap. Once the end cap was installed I used the same needle nose pliers to "pinch" the guide arm back tight around the end cap. The end cap had premanufactured "notches" to hold the end cap in place once the guide arms are pinched down.

Remove top rack stops, slide out upper rack from rack railing, turn over upper rack and attach spray arm using spray arm bearing and screw. Reassemble in reverse order.

Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.

Easy to install cable. Works great now. Hardest part was removing the two phillips screws. (really not hard)

Removed inner panel, replaced failed parts, replaced panel.

Thanks for your fast shipping response. Parts were ordered on Sunday night, you shipped Monday, I got them Tuesday !
Outstanding.

This repair was not difficult except that the part was hard to get to. You need to lay on the ground and the space is small to fit the tools in. It was especially difficult to squeeze the hose clamp on and off. If you are the handy sort and would not be intimidated by pulling the dishwasher out (like I was), then I recommend doing that. Changing the actual part was a breeze and self explanatory. Be sure to shut off the power and water supply to the dishwasher. Bring a towel to soak up residual water in the hose. Watch the video on this site, it was exactly what I needed to see! I was able to fix my mom's dishwasher! What a great feeling!

took the front covers off, used om meter as suggested after disconnecting the wire plug. discovered infinity, so as suggested, determined the valve defective. Ordered over the new valve from this company. After it arrived, took the old valve off by removing it from the bracket. Used the pliers to take the hose off, then unscrewed the supply hose by usung the adjustable wrench. Took the old valve to my shop vise to hold it firmly, then unscrewed the fitting, wrapped the tape suggested and installed it on the new valve. Took it back to the dishwasher, screwed the supply hose on, slipped the hose on and the clamp, turned on the water to check for leaks. Found non, so installed the valve on the frame, turned on the power and checked for filling. Itfilled fine and operated like it was supposed to. Put the front covers back on, and enjoyed praise from wife!!!

I checked for power coming into the dishwasher and up to the main boards using a voltage sensing device which emitted a sound when voltage was present. So initially, I presumed that power to the dishwasher was good. I then replaced the switch interlocks for the door lock, but the dishwasher remained dead. Then I used the multimeter to check the exact volts coming into the main boards and found it was only 39 volts. Next I checked the plug which supplies this power and found a bad connection in the plug. A screw was loose for the neutral wire. I tightened up the screw and with good power, everything worked.

The repair was easy. I followed your online video on the steps needed for the repair. I want to let other customers know that PartSelect sent the right parts needed on my order and they arrived on time. I will order from this company when ever I need to replace parts in the future.

after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!

Easy, just follow instructions on website and do it! Needle nose pliers used to pull out old hub (the old wheels come off too easy) and push the new hub into the old wheel with the edge of the pliers. Eight wheels fix for great "roll" of lower shelf in less than 15 minutes.