EDW6100N00BB General Electric Dishwasher - Instructions

after removing the inside of the door and removing the screws that hold the despenser installing the new one I found that the door now leaked.Itdid not seat properly due to the new unit not seating properly are I had damaged the door panel. I then bought a tube of silicone and sealed the back and front of the despencer and now it works ok. short bottom door seal was returned when I found the leak was around the despenser

Snap the stub/axle into the wheel and snap the assembly on the rack. EZ! This solved the issue where the original wheels (through age) were falling off the rack and the rack would bump over the gap between the body of the dishwasher and the door.

We we're installing a used dishwasher,had to take it back out and replace the water inlet valve.

Ge dropped the ball when they designed the bottom rack. The wheel assembly has two parts a side clipping axle and the wheel. It must be a huge problem in that as soon as you do a search a picture of the these two parts shows up in the first page. $7. 50 As a replacement. There are eight (8) wheel assemblies to deal with. Usually one or two start to fail but the proper remedy is to replace only the axle clips and all of them. ($. 79 Each) reusing the old wheel is key in keeping the cost down. The wheels are not the problem. The easiest way to remove the old axle is to pinch the axle ends. And pull on the clip assembly. Push the new axle clip onto the wheel prior to attaching the clip to the rack. The whole eight clip w/ wheel replacement will take less than 6 minutes. D. Hackett spring hill tn

I read some other fixes on this site. I received the new gasket folded it in half and just pressed it into the channel. Super easy fix.

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.

Wow... Simple... Just pulled the old broken axle off, pushed the new wheel onto the axle then snapped onto the wire basket. Ez and cheap repair but it keeps an off balance dragging sliding from causing more damage.

Used needle nose pliers to get them off.G

Just removed the prior rack and put the new one in. Much improved design on the wheels and rack seems of better material as well. The rack does not have as many holders as the prior rack dishes and pans do not fit as well.

Immediately shut off water supply to the washer. After ordering and receipt ot part: Removed base panel, turned off power, disconnected wire, water supply line and screws attaching washer to kitchen counter. Pulled the washer out and turned it on its side with the valve on top. Removed and replaced the valve, returned the washer to the upright position, pushed it back under the counter, reconnected all services, screws to counter and base panel, turned on the water and power. Took two hours since I needed take a trip to the hardware store to replace a right angle water fitting .

Removed the screws at the inside door edges and lowered front panel. Identified placement of old part, unsnapped it from its mounting, unpluged the ribbon cable and removed the part. Installed the new part in the reverse order.

Replaced all eight wheels. Wheels come in two parts which I used a rubber mallet to gently force the two parts together, then removed each old wheel and replaced with the proper parts (Roller WD12X10074, Roller Stud WD12X10278), new ones appear to be better design and work very well.

I received the part very quickly. I threw away the old rack and put the new one in it's place. No tools or instructions were necessary. The new rack had all of the wheels and combs included. I did not have to purchase them separately. This is a much better designed part than the original rack. The combs are spread differently to better support plates, and the wheels are combined and enclosed to better support the rack. Also, I feel that this was a good price. Thank you!

Wheels on my lower dishwasher rack would come off catch in the door and crack or melt on the heating coil. These replacement wheel stud/axels are a better design and the wheels will not slip off. I am very pleased. Replacement was done without any tools and only took a few minutes.

Before you due anything else...remove the water inlet valve, remove the 4 screws holding the water inlet coupling to the valve housing, remove the nylon filter (tight fit), and clean the debris from the filter. Re insert the filter, reassemble the valve housing and check for leaks. Clears most water flow problems.