EDW4060G03SS General Electric Dishwasher - Instructions

Immediately shut off water supply to the washer. After ordering and receipt ot part: Removed base panel, turned off power, disconnected wire, water supply line and screws attaching washer to kitchen counter. Pulled the washer out and turned it on its side with the valve on top. Removed and replaced the valve, returned the washer to the upright position, pushed it back under the counter, reconnected all services, screws to counter and base panel, turned on the water and power. Took two hours since I needed take a trip to the hardware store to replace a right angle water fitting .

Replaced all eight wheels. Wheels come in two parts which I used a rubber mallet to gently force the two parts together, then removed each old wheel and replaced with the proper parts (Roller WD12X10074, Roller Stud WD12X10278), new ones appear to be better design and work very well.

I received the part very quickly. I threw away the old rack and put the new one in it's place. No tools or instructions were necessary. The new rack had all of the wheels and combs included. I did not have to purchase them separately. This is a much better designed part than the original rack. The combs are spread differently to better support plates, and the wheels are combined and enclosed to better support the rack. Also, I feel that this was a good price. Thank you!

I found Parts Select on the internet and checked out the website. Very easy to use and fund the exact part for my dishwasher. Ordering was simple and delivery was wuicker than expected. Very impressed with your service and will use again in the future as needed.

Wheels on my lower dishwasher rack would come off catch in the door and crack or melt on the heating coil. These replacement wheel stud/axels are a better design and the wheels will not slip off. I am very pleased. Replacement was done without any tools and only took a few minutes.

Before you due anything else...remove the water inlet valve, remove the 4 screws holding the water inlet coupling to the valve housing, remove the nylon filter (tight fit), and clean the debris from the filter. Re insert the filter, reassemble the valve housing and check for leaks. Clears most water flow problems.

Ordered the part from you and it was easy to replace.

In replacing the upper rack in our dishwasher, I struggled and broke one of the end caps (see previous tale of woe. With the new end caps, I finished the job in less than two minutes with no tools. BUY END CAPS when you order a rack!

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

After finding significant water on the floor, misdiagnosed as sump/drainage leak. Replaced inlet sump and pump connector which requires unit to be tipped on side. Otherwise straightforward. Problem was actually a failure to drain. Drain pump running, but water not removed. Each successive step in the cycle added more water, and it eventually overflowed. Had to reinstall unit to determine this, so did that twice. All drain pipes clear. Found small piece of old sump 'latex' blocking drain pump flap valve which I could have looked for when I took it out to replace the sump. Removed blockage and reinstalled. Test drain OK with small bucket of water and rinse only cycle (with water off) just in case. Alignment of the various passages while tightening clamps is important as motor weight can distort rubber parts. I tied the motor up while reassembling.

I removed the wheel slide and installed the axl good as new. My husband was impressed that I saved hundreds in repair bills!

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

Bottom rack has 8 wheels to roll it in and out of the dishwasher for loading. Due to age and wear the wheels kept falling off when the rack was rolled. Snapped off the old wheels by hand, removed the original axle/stud and replaced with the new improved design. Just pushed it into the existing wheels and snapped back onto the rack and worked perfectly. Great inexpensive fix for an annoying problem in less than 5 minutes.

Just took off old wheels and replaced with new wheels and studs. Very simple and news wheels work great.

Using a screw driver I unlatched the door allowing it to open. Removing the 12 or so screws on the inside panel of the door allowed access to the latching mechanism. Removing the broken door latch handle, I replaced it and the new spring. Reattaching the back panel by replacing the screws the job was done.