ED5GVEXVD02 Whirlpool Refrigerator - Instructions

repair went good .only had problem removing tube from clip in front

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

pop in and presto! simple, no tools required, perfect fit.

Ordered a new shelf. Removed the old one and installed the new one. Wife is happy. :-)

Ordered part#PS2341899, received in 2 days. Unplugged refrigerator and removed ice cube drawer. Then removed shelf above icemaker. Used 1/4 nutdriver to remove 3 screws holding the icemaker in place. Then unplugged electrical harness from icemaker. To install, just do the reverse and job could be completed within 10 to 15 minutes. It is not necessary to turn water off in back of refrigerator. You should have ice cubes within a couple of hours, however it takes about 24 hours to fill the ice drawer. Probably saved over $150 by doing it myself.

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I replaced the icemaker assembly. I purchased inlet solenoid valve assembly also, just in case I was wrong. I'll keep it for future use.

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

According to all the information on the internet diagnosing the problem with my in door ice dispenser, the problem seemed to be with the solenoid which I ordered from PartSelect. However, when I got into the repair, I found the problem was with the electrical switch that activated the ice dispenser. A couple of the plastic studs that hold the switch in place had broken which did not allow the switch to be activated. I replaced the small plastic keeper study with small screws and now the ice dispenser works fine.

The retaining pins, which are part of the control bracket, that hold the micro switch that powers on the ice dispensor had broken, allowing the micro switch to fall away from actuator paddle. I replace the entire control bracket which holds the 2 micro switches, one for ice dispensing and one for water.

Ordered new glass shelf installed it.

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Took the part out of the package and installed it. The service I received was excelent. Got the part two days after ordering it