Models > ECKMF90 > Instructions

ECKMF90 Whirlpool Ice Maker - Instructions

All installation instructions for ECKMF90 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the ice maker repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ECKMF90
391-400 of 400
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker would not eject ice from the ice tray.

  • Customer: Todd from Meridian ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

Ice maker stopped making ice

  • Customer: Richard from Stephens City VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

small plastic part in the icemaker control assembly broke, disabling entire system

  • Customer: Linda from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Ice maker would not make ice

  • Customer: Daniel from Central IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

icemaker stopped working

  • Customer: Patricia from Urbandale IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

Frozen-split plastic on old unit

  • Customer: Gary from Fayetteville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Ordered alternate water inlet value-reattached new one as described on enclosed instructions. Newer type inlet connection-was not sure but it worked as described.

Ice maker syopped working pump went bad.

  • Customer: David from Danville IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Straight forward.Vey easy to do

Ice maker quit working

  • Customer: Donald from Banning CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

Ice Maker stopped working. Already replaced Photo Eye

  • Customer: Alfred Van from Lutz FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

Ice maker leaked water from the cube dispensing tray--1 icicle in the rear of tray

  • Customer: Leslie from Columbus OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
We thought that the problem was with the inlet valve, perhaps dispensing too much water and causing the overflow that caused the leak. Installation of the valve was easy, but it didn't fix the leak. After some more tinkering, we discovered that the problem was that the ice maker itself had gotten out of kilter, that the rear part was tilted down too far and was causing the overflow that created the icicle. The rear part of the unit needed to be raised by adjusting the rear screw that attaches the ice maker to the refrigerator. Easy to fix that, and so far, no more leak. It didn't hurt, though, to get a new valve and be forced to clean out the back of the fridge, as well as replace the copper water inlet tube with a plastic one.
All Instructions for the ECKMF90
391-400 of 400