Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E32AF75FPS4 > Parts

E32AF75FPS4 Electrolux Freezer - Parts

All parts for the Electrolux Freezer E32AF75FPS4

Below is a list of all parts for the Electrolux Freezer E32AF75FPS4. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the E32AF75FPS4
1-14 of 169
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.76

Water Inlet Valve

If you notice that the ice maker in your refrigerator is leaking or is not making or dispensing ice, you may need to replace the water inlet valve. When energized, the water inlet ...

$97.59

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$8.13

Defrost Thermostat

This refrigerator defrost thermostat is a genuine OEM part and is sourced directly from the manufacturer. Located on the back wall of the freezer section in the refrigerator, the d...

$18.20

LIGHT BULB

$5.96

SCREW-SHOULDER

Sold individually.

$43.38

Evaporator Fan Motor with Wire Harness - 115V

This evaporator fan motor is 115V. If you notice that your freezer is noisy or is too warm, you may need to replace the evaporator fan motor. This package comes with the evaporator fan motor itself, as well as a wire harness. The evaporator fan motor is in the back of the freezer, so you will need to remove your freezer shelves and the back panel before you can access it. The function of the evaporator fan motor is to circulate air over the coils. The coils convert the heat into cool air, which is then circulated. Be sure to remove the power source from the freezer before you begin this repair.

$9.58

Adjustable Leveling Foot - Black

This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to t...

$12.72

Air Filter

$8.82

GEAR

The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pus...

$27.48

Evaporator Fan Blade

This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of plastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.

$7.42

Single Gasket Retainer Clip

This genuine OEM freezer gasket retainer clip is used on refrigerator freezers, and connects the inner door panel and door gasket to the outer door panel. The gasket is the rubbery...

$6.21

Hinge Mounting Hexagonal Screw

Sold individually.

$34.90

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$44.71

Ice Container

The ice bin, located in a freezer, is a storage container used for storing ice. Ice cubes collect there after they are made. If your bin is cracked or damaged, it is best to replace this part. To repair, first open your freezer door and dump any leftover ice residing in bin before removing it. Next, release ice bin from assembly by releasing the locking tabs. With a flathead screwdriver, flex the tabs inwards on each side. Make sure to bend them enough to unlock and pull assembly from the ice bucket. Line up the new ice bin with assembly before installing it. Refer to the manual provided by the manufacturer for further installation instructions.

All Parts for the E32AF75FPS4
1-14 of 169