Models > E23CS78GSS2 > Instructions

E23CS78GSS2 Electrolux Refrigerator - Instructions

All installation instructions for E23CS78GSS2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS78GSS2
61-75 of 266
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice tray wouldent fill.

  • Customer: Eric from Greensburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

Ice maker non functioning, Ice maker not sending signal for w

  • Customer: Marcus from Bessemer AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 6 people found this instruction helpful
Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.

Refridgerator freezing food

  • Customer: Bob from Gilbert MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 27 people found this instruction helpful
Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

Frost build up on evaporator

  • Customer: B J from Dillingham AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 12 people found this instruction helpful
Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

Ice maker was over filling.

  • Customer: Richard from Marco Island FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.

plastic door holder broken

  • Customer: Bill from Lady LAke FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
took the screw out of the white flange on the top of the door that attaches to the top of the refrigerator. Then removed the cover , and the two screws attached to the refrigerator top. Then lifted off the door removed the bottom plate that is holding the plastic door holder. and replaced the broken part and replaced the bottom plate , set the door back on the hinge and installed the top two screws and the flange cover and the last screw holding the flange cover in place. It actually took longer to type this than the repair

Refrigerator didn't come with racks

  • Customer: Mark from Shorewood MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
The repair was very easy - the door and can racks just click into place. No tools were needed.

PartSelect was helpful to acquire the parts.

ICEMAKER BROKEN

  • Customer: Philip from Hemet CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
I GOT THE PART, HITCHED IT UP
AND IT STARTED WORKING RIGHT AWAY
IT FIT IN EASILY, AND THE DIRECTIONS WERE EASY TO FOLLOW
THANK YOU

No Water or Ice Dispensing

  • Customer: Levi from Ambler PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Leaking water valve

  • Customer: Robert from Liberty Twp OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

My Frigidaire Drawer Broke

  • Customer: David from Coppell TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
My Frigidaire Drawer broke... I ordered the parts and installed it within 5 min. It took more time to remove the food and drawer then it did to install the pegs.

Crisper bin track support

  • Customer: Ruth from Lake Forest CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches

Broken Shelf Support Stud

  • Customer: Kristina from Woodbridge VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

Support stude for both vegetable crispers broken off

  • Customer: RANDY from NORTH CHARLESTON SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

freezer filled up with ice leaking from ice maker shut off valve bad

  • Customer: Harry from Orange City FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 5 people found this instruction helpful
It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.
All Instructions for the E23CS78GSS2
61-75 of 266