Models > E23CS78EPS0 > Instructions

E23CS78EPS0 Electrolux Refrigerator - Instructions

All installation instructions for E23CS78EPS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS78EPS0
256-270 of 283
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

When the ice maker was filling the ice tray with water, the water would come out the water dispenser at the same time.

  • Customer: Greg from Murrieta CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

broken crisper drawer support

  • Customer: Genevieve from Herndon VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Ice maker stopped making ice. Ice was in the maker but would not dispense.

  • Customer: Michael from Cherry Hill NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Loosened 2 screws, slid the old ice maker up, disconnected power source. Revolved old ice maker. Reversed steps and was up and running in no time. Quick shipping too. Didn't pay extra and received it in 2 days.

missing glass shelf

  • Customer: Joyce from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Open box, peal plastic off of glass, slide glass onto shelf brackets

The crisper glass had broken

  • Customer: Christopher from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.

light bilb went out

  • Customer: Denise from Landover MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced it

water valve leaking

  • Customer: Anthony from Indiana PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

Crisper Cover support had broken

  • Customer: M Jerdone from Seneca SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I watched your video on how to do the procedure and followed it, step-by-step. It worked like a charm. When I took the crisper drawer and runner out of the refrigerator, I noticed that the lower drawer support had broken as well. So, I have ordered 4 to have a few on hand and will repeat the process when my new order arrives. I'm very pleased! Thank you very much.

Everything in the refrigerator side was freezing.

  • Customer: Efrain from Union City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The defrost thermostat kit is located in the freezer side of the refrigertor. I turned off the electrical breaker for the refrigerator. I began the project by removing all the frozen food on the lower half of the freezer. I removed the racks and 3 rails on both sides using a cordless drill with a 1/4" socket and located panel. The panel had 4 1/4" screws holding it to the back of the freezer. I removed all screws and the panel came out easy. I located the defrost thermostat and with some wire cutters, I cut the wires. I connected the the new defrost thermostat with wire connectors and reattached it to the copper tube I removed it from. I put the panel back on along with the side rails and racks.. This project was very easy.

loud noise fan blade broke,off balance

  • Customer: EDWIN from ELWOOD IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

ice maker not working

  • Customer: john from richmond KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
used nut driver to loosen 2 screws partially. slightly lifted up ice-maker and pulled out. unpluged the ice maker from socket and removed. i timed myself. 4 minutes to take out and replace new one. glad i did not call repairman. wife skeptical at first until we started hearing the ice fall.

crisper supports were broken

  • Customer: Catherine from Richland Center WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the do it yourself video which helped tremendously. My husband was busy so I was able to do it myself.

No Ice

  • Customer: Glen from Black River Falls WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Ice Maker/Water Solenoid Valve Assembly

  • Customer: Kenny Keith from Terra Haute IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

Water Actuator (dispensing paddle) broke and not able to glue again

  • Customer: Robert from Fort Myers FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Fortunately, this was not hte first time to do a repair on the through the door dispensers. I turned the unit off and removed the door tray (slides out) to expose the screws for trim removal. When that is removed, you remove the circuitry and then remove the actuator and spring. It was difficult to get the new actuator in place. the "stop" which holds it in pace is not forgiviing! And that is being mild. (I remember a few explitive delitives I thought wer gone foreever! I reconnected the circuit to the panel, replaced the panel, and the tricky part was to reinsert the water hose into the dispenser hole. Good luck. When that was in, the entire unit was reeturned with the four screws. The front trim panel was replaced with four screws, and the slide in drip tray was slid in. Job done, and the power was restored. Thank goodness I had some long hemostates to control the reinsertion of the water tube!
All Instructions for the E23CS78EPS0
256-270 of 283