E23CS78DSS3 Electrolux Refrigerator - Instructions

Fortunately, this was not hte first time to do a repair on the through the door dispensers. I turned the unit off and removed the door tray (slides out) to expose the screws for trim removal. When that is removed, you remove the circuitry and then remove the actuator and spring. It was difficult to get the new actuator in place. the "stop" which holds it in pace is not forgiviing! And that is being mild. (I remember a few explitive delitives I thought wer gone foreever! I reconnected the circuit to the panel, replaced the panel, and the tricky part was to reinsert the water hose into the dispenser hole. Good luck. When that was in, the entire unit was reeturned with the four screws. The front trim panel was replaced with four screws, and the slide in drip tray was slid in. Job done, and the power was restored. Thank goodness I had some long hemostates to control the reinsertion of the water tube!

took old valve off one peice of it was broke off from freeze replaced it with new valve all but one conection was quick connect electric connections were color coded quick fix works fine thanks Gary

Pushed the "release button" and took out old filter. Pushed the new filter in place until it 'snapped in place.' Then ran the 'water' until it stopped spitting out air.

The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.

I followed the video instructions from your site and it couldn't have been easier.

electrical unplugged. water turned off and disconnected. cardborad backing off (4 screws). removed part (2 screws). unplugged electrical connections. removed each line one at a time and inserted into new part, connected electrical connections. placed new part with all connections back onto refrigerator, (2 screws), backing back on, water line connected, and electrical connected. no leaks with new part. simple uninstall and install for do-it-yourselfer. instructions need to be printed in larger font for easier reading.

I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

replaced with kit, very easy unplug unsrew and replace, any one can do it

When my wife and kids moved down they lost the upper bracket and the screw for the lower cam. parts show up and matched perfectly to the orginal no issues at all

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

We watched u tube repairman then did exactly the same thing. Then we did a high five.

To describe this replacement as "really easy" is an understatement! The hardest part was digging the socket set out of the tool box. The instructions were well written, as were descriptions of fellow home do it yourself types. Those gave me the confidence to just for it. I am so tickled with myself and the money I saved! My hubby is pretty impressed too! Cathy

followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)