E23CS78DSS0 Electrolux Refrigerator - Instructions

ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John

Removed the ice maker cover on the front (6 screws)...took off old parts and installed new ones....very easy... replaced front cover and no more frost build up in the freezer.

Because of the design of the support, this could have been a difficult job. However, with the video that was provided when I selected the part, it was not a problem. All you have to do is knock the center pin through the support and remove the old support. Pull the pin out of the wall of the unit and push the new support in and drive the new pin in until it is flush. That's it!

Ordering replacement parts was easy! Expected a simple pull out old plug, insert new plug.... Not sure if it comes from factory like this or if this had been previously repaired poorly, but the broken plug was heavily glued in place. Took some serious finess work to remove without serious damage. Once out, it was simple plug in

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!

Loosened 2 screws, slid the old ice maker up, disconnected power source. Revolved old ice maker. Reversed steps and was up and running in no time. Quick shipping too. Didn't pay extra and received it in 2 days.

Open box, peal plastic off of glass, slide glass onto shelf brackets

The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.

followed the video instructions and wa-la! Saved my money by not calling the repair man, the shipment of my part was fast, and the repair was even faster. Thank you for helping me in my repairs. Very Satisfied!!! Carol

Removed the right door. Removed three bolts that hold on the door on. Once removed, I removed the bushing with a screw driver and popped the new one in. Replaced the door and no more noise. Fixed the problem. I also watched a you tube video before I started.

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

The repair was a piece of cake. After a previous day of hours being spent. This was the easiest repair ever. Thank You