E23CS75DSSH Electrolux Refrigerator - Instructions

Easily removed the refrigerator door, layed it across a table, popped out the lower hinge bearing and lightly tapped in the new one. Reinstalled the door and adjusted alignment. Popping noise gone.

First I don't think I would have tried this if not for the video posted on your page. If was highly professionally done with good sound and video quality. Thank you for that. Once I saw that I ordered my part. Took the door off and found the broken part. It was the top bearing. It had broken in two and the shaft part had to be pulled out using needle nosed pilfers which took for of the time for the repair. If I had thought about it I should have ordered the lower one also and replaced that both at the same time, but it worked out for me and I got the door back on which now works as it should. And thank you for checking back with me on the repair. You have a very thoughtful company looking after your clients.

Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.

The original part broke. The plastic attachment end of the part snapped off. The new part was easy to attach.

Undo a few bolts unplug power and unhook water lines then recut all lines and push in to new value

Well, after watching the video before ordering the part, I ordered the correct part. My wife had ordered the wrong part that I had to return and ordered the correct one. To install the glass you just take out the crisper above shelf and lay the glass in place. So simple.

Following previous installation instructions was very useful. Would add that the nut driver needs to be 1/4 in and to release the water lines from the valve body, simply squeeze the blue ring toward the valve and pull on the water lines at the same time. Simple fix!

Write down where tubing goes, wiring is color coded.

Nothing exciting - just replaced the defective drawer covers with the new parts. The guides are poorly designed. the bottom guides on both covers failed.

carefully removed retainer from old valve

The u tube instructions were exactly what is needed. I had to cut off the old plastic pipes. My pipe had threaded connectors. Pex push on connection is super easy. You don't really need a block of wood to cut it if you have a sharp utility blade. If if you are sure this is the problem this is a really easy fix. Steps 1 turn off water at wall unplug electric also 2. Disc line at valve on refrigerator 3. Remove 2 screws holding valve 4. Pull valve out and remove plastic hoses and electric connections pay attention to color of pipe and electric connection. Mine were color coded. Had to cut off thread connectors. Reattach in reverse order or do one at a time. Check for leaks.

I followed the video and everything went smoothly. After pushing the pin in I pulled out the broken pin with needle nose pliers-very easy just like on the video. It took more time finding all the simple tools than the job itself-well almost!

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!