E23CS75DSS5 Electrolux Refrigerator - Instructions

Loosened 2 screws, slid the old ice maker up, disconnected power source. Revolved old ice maker. Reversed steps and was up and running in no time. Quick shipping too. Didn't pay extra and received it in 2 days.

Open box, peal plastic off of glass, slide glass onto shelf brackets

The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.

followed the video instructions and wa-la! Saved my money by not calling the repair man, the shipment of my part was fast, and the repair was even faster. Thank you for helping me in my repairs. Very Satisfied!!! Carol

Removed the right door. Removed three bolts that hold on the door on. Once removed, I removed the bushing with a screw driver and popped the new one in. Replaced the door and no more noise. Fixed the problem. I also watched a you tube video before I started.

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

The repair was a piece of cake. After a previous day of hours being spent. This was the easiest repair ever. Thank You

I suspected that the On/Off Switch was the problem. (Pressing and holding the switch 'on' for 15 seconds to recycle the icemaker did not bring the ice level control arm to life.) I decided to replace the whole icemaker rather than just the switch. (Do not try to replace the switch...almost impossible.) Steps: 1/Remove the Icecream shelf (lift up the front lip and pull out; 2/remove the Icecube holder tray (lift up the front and pull out.) 3/Remove the two hex head screws which are facing you above the ice maker. 4/Pull the icemaker slowly out and and down to reveal the electrical wiring, and unplug the electrical plug. 5/Follow new instructions re the water hopper and the ice-flapper-thingy on the new icemaker, and turn the new switch to 'off' before you start to install it. 6/Plug in the new icemaker, and push the electrical wiring down to the left as you push the icemaker into place, make sure the back edge of the water hopper goes under the water spout. 7/Replace and tighten the two hex head screws. 8/Press and hold the switch 'on' for 15 seconds or more to cycle the icemaker (the ice level control arm will slowly raise up and then go back down). 9/Replace the Tray and the Shelf. 10/Allow the icemaker time to cool and freeze the newly injected water.(This may take up to 6 hours.) 11/Listen for the sweet sound of the dropping icecubes.

Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

just put it in the old hole. the hard part was getting the old one out. you have to poke the center piece in to remove. otherwise you will break your fridge. then you have to to pull the center piece out before you put new in.

husband did it took only a few min part was easy to find

Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

take of the tray & take parts out & installed the new ones

Removed the nuts on top - to loosen the door. Lifted the door off the hinge. Took out old part, put in new one, reinserted door, replaced nuts.

I was quoted $200+ by an appliance repair man. I found the needed part and instructions on this site and rest is history. The install was easy, delivery was amazingly fast and now I have a working water lever on my refrigerator. Thank you partselect....