Models > E23CS75DSS5

E23CS75DSS5 Electrolux Refrigerator - Overview

Get Parts and Repair Help for E23CS75DSS5

If you know the refrigerator repair part you need, you can browse the list of all parts on the E23CS75DSS5, or you can search by name or part description. You can also find your part by where it is located on the E23CS75DSS5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for E23CS75DSS5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.84

Crisper Support - Rear

This part can be used for the rear support. Sold individually and mounts to the inside cabinet wall.

$2.72

Crisper Cover Support - Front

This part can be used for the front support. Sold individually and mounts to the inside cabinet wall.

$58.26

Water Inlet Valve

The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact ice maker mold.

$6.67

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$11.50

Defrost Thermostat Kit

This kit includes the clip, leads and heat shrink.

$80.57

Water Dispenser Actuator

Once a glass is pressed against the actuator pad it will cause the dispenser to deliver ice or water when activated.

$20.66

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$29.59

Crisper Drawer Cover - NO Glass

This part contains molded glide rails for the crisper pan. It does not come with the glass shelving. The glass is not included. Must be ordered separately.

$90.07

Rear-Mount Ice Maker Assembly

This icemaker mounts to the back panel in the freezer section of the side by side refrigerator. This kit includes the icemaker, power cord, bail arm and fill cup.

$25.71

Dispenser Crusher Housing

This part may look different or be a different color than the original, but will fit and function the same as the original part.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking out of refrigerator

  • Customer: Jose from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 181 of 219 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in p... read more

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 160 of 165 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Water dispenser actuator snapped in half

  • Customer: Jerome from Yardville NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 143 of 159 people found this instruction helpful
Unplugged refrigerator. Pull forward on tray at bottom of water & ice dispenser to remove it. Remove three screws. Push up and then pull out to remove black cover around dispensers. Be careful not to break ribbon cable. Pulled ribbon cable from green circuit card on the cover. Set the cover aside. Removed green circuit card from refigerator (six small... read more