DWUA500AAX Admiral Dishwasher - Instructions

Removed the old door gasket. Adjusted the new gasket to fit evenly on both sides. Removed the seven hex screws. Two nuts holding the cover over the backside of the cover for the soap dispenser. Removed the old grommet, replace the new one. Cleaned up the inside and replace screws. Truly was easy.

The hardest part was figuring out how to get the dishwasher out from the cabinet. Your instructional video said "no tools are needed" but that turned out to be untrue.

It was very easy. Simply remove old seal with a pair of needle nose pliers. Clean or scrap any build-up from old seal location and then push-in the new door seal. Close door and let the new seal form to the door.

Pulled the old gasket out, put the new one in place.Used a screwdriver and fingers to push the new gasket firmly into its seat. Repair done. I've done a few repairs in my day, none easier than this.

Followed directions on site video. Total time 5 minutes. Leak repaired

I grabbed a hold of the old gasket and removed it. I then took the new gasket and set it in place on one corner. I inserted it around the groove and with just one adjustment for length, I took the round bottom of a spoon to set and smooth the gasket into place. No more leaks. 5 minute fix.

Replaced door seal, very easy!

I read about the repairs and problems also watched the videos on partselect web sight. It was very help full to read about replacing the door seal and still have leaking witch led me to pull the door apart to find the soap latch seal leaking badly, actually door seal was leaking too , part was here in 2 days and the dishwasher is back up and running now, no more leaks, I did run a fan on inside of door to dry out the insulation for a day and a half. Thanks partselect for great service. Jed from Wisconsin.

Removed the upper rack rail stops. Removed the upper rack by pulling outward until the rack rollers cleared the rails. Attached the new roller on the upper rack. You can look at the other undamaged rollers to see how they lock into place. re-install the upper rack by feeding the upper rack rollers back onto the rails. Install the rail stops back into the rail ends,and the job is complete. VERY EASY!

I had to call an appliance repairman to come fix it. If I would have been able to pull the dishwasher out, it would have been a simple fix. It would not come out and I loosened to water line trying therefore causing more problems.

WE installed a new door gasket. However the machine still had a leak only on the left side. Called a tech and he came and said the gasket was installed backwards. Apparently the original one was also because we installed the new gasket exactly the way the old one was. We are all set now.

I opened the door, and looked at the upper shower fixture ( a spining arm with holes in it) and saw there was a star shaped object that appeared to be the attaching screw device for the top shower. With my rignt hand I grabbed the points on the star and easily rotated them counter-clockwise, until the upper shower fixture came off in my hand. Next, I removed the top end of the pre-formed plastic tube from the top of the tub. I laid on my back so I could see under the tub (where the plastic tube is joined to the actual pump). The tube is connected to the tub via a rubber hose fitting. I unscrewed the rubber hose clamp and removed the pre-formed plastic tube. Disassembly was then complete and you simply reverse the procedure. Took less than 15 minutes. My diswasher is now back to working properly.

Turned off the supply valve. Disconnected the power. Removed the water inlet and outlet lines. Removed the old valve. Installed the new valve and reversed the previous action. Installed a new outlet clamp on the hose (highly recommended).

Exactly like the video...everything went well

Opened circuit breaker feeding dishwasher Removed the 10 screws from the inside panel on the door. Unplugged two quick disconnect plugs. Removed the wax motor (actuating solenoid). Installed the new one from Parts Select. Reconnected the plugs. Replaced the cover and 10 screws. Turned the breaker on and ran a load of dishes. worked perfectly.