Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DWD1500AWB > Instructions

DWD1500AWB Admiral Dishwasher - Instructions

All installation instructions for DWD1500AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DWD1500AWB
76-90 of 500
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken handle

  • Customer: Simon from North Syracuse, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
Easiest repair ever! 11 sized T20 screws hold the plastic to the door. Remove those and the handle just sits there. Disconnect the leads from the old and attach to the new. Total repair time under 10 minutes, and I'm NOT a handy guy.

Dishwasher filled normally with water and seemed to be cycling normally, but after cycle complete, no washing had occurred.

  • Customer: Kenneth from Brandon, MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Thus it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.

If you don't hold door when opening, it will drop down hard

  • Customer: Peter from Westbury, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

Dishes not getting clean. Tear in the filter.

  • Customer: Harry from camas, WA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 5 of 8 people found this instruction helpful
Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

humidity would seep out absorbing into the granite above

  • Customer: Eric from Overland Park, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

the dishwaster was not getting the dishes clean

  • Customer: Mike from Lansing, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

Dishwasher was leaking during wash cycle out the front door

  • Customer: John from Holllis, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Replaced the door gasket, inner foam strip and the bottom seals on the door. Unfortunately I broke the plastic door latch handle in the process and had to purchase a complete latch assembly too.

Lower basket wheels fell off and were melted

  • Customer: Michael from Denver, CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

dishes not clean

  • Customer: David from Lake Zurich, IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

Soap dish full of west soap, dishes not clean: Isolated to stripped pump shaft, foreign object jammed chopper

  • Customer: Tom from Centreville, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

Upper wash arm would not turn.

  • Customer: David from Fayetteville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Snapped the old part out and snapped the new part in.
It was a piece of cake.

broken chopper

  • Customer: Alain from Lake Mills, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

Latch on soap dispenser door broke

  • Customer: Ronald from Longmont, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

The dishwasher got the dishes dirty not clean

  • Customer: Ken from Mapleton, UT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Handle broke

  • Customer: James from Springfield, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the inter door panel replaced broken handle put panel back washed dishes
All Instructions for the DWD1500AWB
76-90 of 500