DW761B Jenn-Air Dishwasher - Instructions

Took out the pins that hold the detergent cup on, beginning with the side without the spring. Make sure you check how the side with the spring is installed before you take it out. If it's not done right when you put the new one on the lid won't spring open. Then installed the new detergent cup lid. Easy as pie and it would have cost $50 to just have someone come out to look at it and this cost $12. Can't beat that!

Turned off power to machine t breaker. Open door and removed inside cover of door by reoving screws along edge. Removed panel over door switch. Unpluged old switch and pluged newswitch in. Replacd pannel and inside door cover. Turned power back on and washed dishes.

It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.

Removed the inner door panel-Removed the black cowling covering the timer and wires.
Removed the swicth assembly and installed new part.
Reassembled dishwasher.

I checked the operation of the two switches. One switch did not click, when button was pushed, as cleanly as the other. There was a bit of delay and play in the button when depressed, even sticking a bit.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

This is the second time I've purchased parts from PartSelect.com. Actually called Lowe's parts hotline and got disconnected three times. Went online with PartSelect.com and purchased the items within 5 minutes. Parts arrived within 2 days. Will definitely be purchasing parts from PartSelect.com again when needed!!!

I hand screwed the pieces together and screwed them by hand into the proper location in the dish washer. I turned on the dishwasher and it worked !!!!

My dishwasher hasn't been working for 6 years because of this broken part and I couldn't afford the house call of a tech. When I found your site I realized I could do it myself !

ALL HAIL PARTSELECT.COM!!!!!!!!

Thanks to your diagrams and easy to order parts I am a happy homemaker !!!!!

turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!

Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.

I used the parts blowup diagram on PartSelect.com and dissasembled the bottom wash assembly. Carefully examining how the washer arm rotated, I determined that the spray arm support nut had broken. The extended top of it has broken off. This nut, when tightened, allows the spray arm to rotate freely. In trying to diagnose the problem, I had even removed the motor assembly at the very bottom. When I reassembled it, I apparently did not seat the gasket well and did not tighten the bolts well, so when I tested the washer, water leaked out the bottom. So, I had to dissasemble it all again and properly torque the bolts. So, I really created another problem during the diagnosis.

After checking this site for any clues I saw that others had the same problem and changed the door switch so I thought I would give it a shot.I removed the inner part of the door(plastic).It had about 8 screws.Then there was a plastic cover that covers the wiring that comes right out and there was the switch.There are really 2 switches that come with the latch.then take out one screw with the nut driver.Take the four wires off the old latch and install on the new latch.Then screw back into the door and put inside part of the door together.Close the door and turn on and away you go.I also turned off the power to play it safe.I was thinking of replacing the dishwasher cause it is 10 years old but now I can take my time and wait for a good deal.Thank you very much partselect.Also I ordered the part 12.00 Sunday nite and recieved it on Tuesday afternoon with no special shipping.Wow!

First unplug the unit. Open door. Take a special tool to remove all the screws (star shaped) around the edge of the door, and remove plastic panel where motor for detergent cup sits. Remove wires (two) from the motor. Remove wax motor by unsnapping motor from its cradle--comes out by moving the fingers holding it in. Push new motor into position, being sure the round pin sticking out at the end (on the left side) so that it sits in the groove made for it. Replace panel and screws, plug power cable back into its box. Close detergent cup door, turm on dishwasher, run through cycle, open door and check to see if detergent door opened up. If it did, then fill with dishes and wash.

First, I searched the repair help on this site to see what others did to repair their diswashers, and it looked easy, so I just followed the same instructions. First, I used a hex star key wrench to remove the screws that hold in the interior door cover. I disconnected the leads to the defective wax motor, reconnected the leads to the new motor and screwed the door back together. It took 15-20 minutes and was a piece of cake! My first appliance repair, and as a single woman and first-time homeowner, I was really impressed with this site! It gave me confidence to tackle more home repairs instead of calling for service and getting raked over the coals.

The replacement part was the perfect size but the threading on the terminal ends was increases to 1/2" v the 7/16" from the previous element. My first attempt was to find a similar type of part at the local hardware store(not a superstore)since I planned to replace the grommets anyway. After not having any success, I came home and modified the fasteners by slowly drilling out the id of the fasteners until they threaded properly. The time to replace after the drill out was less than 10 min and the ~$45.00 is significantly less than $450.00 for a new unit.
If I would ask anything of part select, it would be to include fastening hardware as re-engineering of products is a continual process.