DU2JV Magic Chef Dishwasher - Instructions

First I had to unhook the electric, water line and drain hose. Then slide out the dishwasher. Took several days to find the drain hose - local stores only carried a 6 ft hose and I needed a 7 ft. Once I found it online, purchased it and recieved it I put it all back together and all is good.

Took off the float, the jam nut was hard to get off, we ended up breaking the bottom piece of the float to get it off, but that was okay because we had a new float. The new float went on real easy and the jam nut went back on real easy. The foam insulation strip was real easy to get off we got a good hold of one end and striped it off slowly so there was nothing left on the door, then we cleaned the surface and put on the new insulation strip. We ran dishwasher to test it and there was no leak. Awesome. Cheap and easy to repair. We were impressed.

Once I pulled the old broken drain valve lever lifter off the shaft, the shaft rotated counter clockwise. I then had to turn shaft back clockwise so there was enough room to slip the new part on. Needle nose pliers worked great to hold it in place while regular pliers in the other hand was used to turn the shaft.

Sooooooooo, I ordered a new kick plate, it arrived promptly, tried installing it and it was being difficult. Removed plate above that and lined up new plate(kick plate) tried putting plate above it on and as when we installed the machine that upper plate was difficult. Removed upper plate to fcheck problem of installation and guess what? Stuck in the inside of the upper plate was the lower plate complete with sound insulation. Happy ending :-)

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

removed inner door panel. tested ythe Wax motor that operates the soap dispenser latch. It tested OK so I removed dispenser assembly. replaced the worn plastic parts and reinstalled the inner door panel.

I used a torx driver to remove the seven screws holding the inside door panel in place. Flipping it over exposed the dispenser mechanism. There were two hex nut screws holding the whole assembly in place and two wires attached to the wax motor. As an afterthought I had ordered the sealing grommet for the latch, and as it turned out, the main problem with the sticking latch was that the grommet had worn out and allowed the hard soapy water to leak into the slider assembly and build up a hard crusty residue that had helped to ware out the old wax motor. After completely disassembling all of the parts, I scrubbed the residue out of the housing, replaced the slider, latch, spring, and grommet. Next I snapped the new wax motor into place and connected the two wires. The whole thing went back in place and the two hex screws went back to hold it all together. Finally, the seven torx screws went back to put the door back together. The whole repair went without a hitch.

Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.

This is the second time I've purchased parts from PartSelect.com. Actually called Lowe's parts hotline and got disconnected three times. Went online with PartSelect.com and purchased the items within 5 minutes. Parts arrived within 2 days. Will definitely be purchasing parts from PartSelect.com again when needed!!!

I hand screwed the pieces together and screwed them by hand into the proper location in the dish washer. I turned on the dishwasher and it worked !!!!

My dishwasher hasn't been working for 6 years because of this broken part and I couldn't afford the house call of a tech. When I found your site I realized I could do it myself !

ALL HAIL PARTSELECT.COM!!!!!!!!

Thanks to your diagrams and easy to order parts I am a happy homemaker !!!!!

The replacement part was the perfect size but the threading on the terminal ends was increases to 1/2" v the 7/16" from the previous element. My first attempt was to find a similar type of part at the local hardware store(not a superstore)since I planned to replace the grommets anyway. After not having any success, I came home and modified the fasteners by slowly drilling out the id of the fasteners until they threaded properly. The time to replace after the drill out was less than 10 min and the ~$45.00 is significantly less than $450.00 for a new unit.
If I would ask anything of part select, it would be to include fastening hardware as re-engineering of products is a continual process.

First, I searched the repair help on this site to see what others did to repair their diswashers, and it looked easy, so I just followed the same instructions. First, I used a hex star key wrench to remove the screws that hold in the interior door cover. I disconnected the leads to the defective wax motor, reconnected the leads to the new motor and screwed the door back together. It took 15-20 minutes and was a piece of cake! My first appliance repair, and as a single woman and first-time homeowner, I was really impressed with this site! It gave me confidence to tackle more home repairs instead of calling for service and getting raked over the coals.

First unplug the unit. Open door. Take a special tool to remove all the screws (star shaped) around the edge of the door, and remove plastic panel where motor for detergent cup sits. Remove wires (two) from the motor. Remove wax motor by unsnapping motor from its cradle--comes out by moving the fingers holding it in. Push new motor into position, being sure the round pin sticking out at the end (on the left side) so that it sits in the groove made for it. Replace panel and screws, plug power cable back into its box. Close detergent cup door, turm on dishwasher, run through cycle, open door and check to see if detergent door opened up. If it did, then fill with dishes and wash.