DU2J Magic Chef Dishwasher - Instructions

Ordered parts on Saturday, and they arrived Tuesday. Followed the instructions in the video. It could not be easier. I may turn pro when I retire.

Orient the gasket so that the more squishable hollow side of the gasket faces the door, and check that the length is sufficient to fill ths entire channel. The less compressible side goes into the channel, which requires some skill and strength to seat well. The flat portion of the more or less square gasket has two edges to it. What works best is to put the edge that is toward the inside of the dishwasher into the channel with your fingers, and then press in the other edge firmly with the small spatula of about 2 or 2and 1/2 inches until you can no longer see that edge. This is the visual indication it is seated. in the corners you may only be able to use a corner of the spatula.

Installed a new grommet on the soap door latch. Replaced door seal at customer request. The door seal ordered was to short. Replaced door spring clips at customer request. Split the door, remove 2 screws from inside the inner panel, grommet is between the inner panel and latch mechanism. Line the new grommet before install.

unscrewed 7 torx screws with the impact driver. removed the motor from the bracket. comes out pretty easily. moved wires aside. Pulled the wires off the motor using the pliers- one came off very hard, note where they go, corroded in place. installed the new motor by easily re-attaching the leads. Biggest surprise was that there were 2 motors. I initially replaced the lower one which did not solve the problem. When I replaced the upper, it worked. Not sure of the function of the lower motor. The upper one clearly fits into a slot which seems to attach to the doors.

Not well! Could use some guidance. I replaced the shaft seal, shaft seal washer, "D" shaft "E" clips, solenoid bracket, assorted screws and the pull solenoid. When replacing the seal shaft I moved the "D" shaft to far and it disconnected the lifter from the drain flapper flapper assembly and flapper spring. Since I do not have, and was not able to locate in my area or on line, a service manual for this machine, I had to go by a parts schematic that I received on line from Jenn-Air. Consequently, I wasn't sure on the reinstallation of all these parts. Since the plastic lifter can only be installed one way on the "D" shaft, it is believed that the flapper spring arm goes between the two prongs on the lifter. After completing the assembly as described above, I now have a situation where the dishwasher will not drain. The pull solenoid seems to work as designed, but when it goes into a drain cycle, it will not drain. Any suggestions, thoughts, recommendations or a copy of a service manual for this repair would be appreciated. Bill

simply replaced the ring and the water inlet injector, no tools need on that part of the repair

Was so easy. I am an old grandmother. I looked for parts for the dishwasher and happened on this site. When describing the problem, I said "won't start". The part number came up and I bought it. Took about 3 days for part to arrive and less than 15 min to install. So easy and if I had problems there was a step by step guide on internet. I am 100% satisfied and recommend for anyone even if you are not handy.

Go to computer, log onto PartSelect, order part. Two days later, go to mailbox, open package. Go back to computer, log onto PartSelect, watch instructional video on how to install the part. Go to kitchen, do what the video showed you to do. Job done.

First replaced the door seal, that slowed it down substantially, but not totally. Next replaced inner door foam insulation strip and that took care of it, no more leaks. There was some corrosion evident after I scraped off the old strip, sanded that smooth with emery sandpaper and then installed new strip. Job done!

Followed the outstanding video instructions. Your company is fantastic. Your attention to detail, the quick shipment (one day) and video ... stellar! We will be referring your company to all!!! Thank you!!!!

replaced with new gasket and it works great.

Followed the video on the websight

Because mine is a portable dishwasher, I had to remove top first. the sides and back are one complete unit. the torque screws are in the front, 2 on top, and 2 in rear. Then the panels can slide back to access the spring. Replace the plastic piece & hooked on the spring. Reassemble in reverse order.

Well, I haven't gotten the right part yet. I'm such an idiot that I've ordered the wrong part twice now. So, figuring that 3's a charm, I'm going to try to get the right part now. I do have to say that part select has made it amazingly easy to return the parts. And both of the first 2 (wrong) parts arrived within 2 days of ordering. I'm pretty impressed with this company. Now, if I can just order the right part, I can tell you how the installation went!

Followed the video found on the website. Very simple repair. Saved $120 by getting the part and fixing myself.