Models > DU1055XTVS1 > Instructions

DU1055XTVS1 Whirlpool Dishwasher - Instructions

All installation instructions for DU1055XTVS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DU1055XTVS1
1-15 of 342
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 193 of 204 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 106 of 118 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.

would not turn on

  • Customer: Douglas from Dallas GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 69 of 83 people found this instruction helpful
I did a search on the website and read the instructions for trouble shooting. I took the inside door off by taking the screws out. I pulled the part and tested it and found it did not in fact have no ampage. I then ordered the part on line. It came in two days, I plugged it in, put the door back together and the total time was about 15-20 minutes. Easy, simple, great instructions and the entire thing only costed me the part itself. It's working great now! And I've never worked on appliances before.

dispenser didn't stay closed

  • Customer: Burt from Richardson TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 57 of 62 people found this instruction helpful
Ordered new part and installed it. I found a repair manual online and the replacement was pretty easy. I removed 8 screws that held the outer door and the dispenser was sitting there looking at me. I disconnected the solenoid, pried apart two clips and the old dispenser came right out. Reversed the process to install the new one.

Heater element broken.

  • Customer: Dennis from Sedro Woolley WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 55 of 60 people found this instruction helpful
Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts holding element in place.

Step 8: Remove element.

Step 9: Reverse Steps 1-7.

Step 10: Drink beer.

Dishwasher was taking way too long to go through its normal cycle; the indicator lite did not advance to DRY.

  • Customer: Robert from Burlington NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 55 of 64 people found this instruction helpful
Remove just the 6 Phillips screws holding the control panel assembly to the top of the door. Panel lifted off, clearing the latch assembly. Rested it on my knees as I sat in front on a chair. Control board is right there. Wiring plugs easily pulled off the old board. Their locations are clearly marked on the board by wire colors. Removed screws holding old board, replaced with new one, plugged wires onto the new board. Screwed the control panel back on the door, being careful to clear the door latch assembly. Ran the dishwasher through a test cycle (time not included in the repair)and it works like new. Probably saved $150. in labor service charge.

Cap came off and melted

  • Customer: James from Mesquite TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 41 of 41 people found this instruction helpful
Opened door and installed cap. Not much effort. But really got good service from Parts Select. Received order much faster than I had expected.

Wanted to replace white panel with stainless steel to match other appliances.

  • Customer: Sandra from McKinney TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 43 of 50 people found this instruction helpful
My husband removed the existing panel by removing the retaining screws. Installed the new panel and replaced the screws. Very pleased with the new look and how easy it was.

spinner kept falling off

  • Customer: paul from erie CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 40 of 49 people found this instruction helpful
i removed the top screw for the water input to the spinner, which gave me enough room to replace the worn nipple pin that the spinner snaps on to. then snapped the new spinner in place. and then screwed everything back into place.

The door gasket stuck to the door a pulled out of place after every use

  • Customer: Penny from Manchester MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 43 of 61 people found this instruction helpful
Worked the new gasket into the groove with a smooth screwdriver and my fingers. No leaks and it stays in place. Parts Select had the right part and I got it fast

Needed to replace the whole dish soap dispenser

  • Customer: Jessica from Plano TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 34 of 41 people found this instruction helpful
I switched off power to the dishwasher and unscrewed the front panel from the inside sides. Then, carefully removed the front by lifting up and off. I disconnected the signal wire by unclipping it from the detergent dispenser; it clipped in like a phone jack. Unscrewed the frame holding in the dispenser, then popped out the old dispenser, popped in the new one, screwed on the frame, hooked the signal back in. Replaced the front, screwed it in, turned on power and ran a small quick wash to make sure it was working properly. It was!

Water leaking from front right corner (door) while washer running

  • Customer: Clifford from Centennial CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 29 of 31 people found this instruction helpful
The hardest part of this was figuring out the cause of the leak. It only leaked while the washer was running (arms spinning). I thought it might be the air intake seal at the lower part of the door-but that did not look damaged.
I cleaned off the door gasket really good and that slowed the leak - so I figured the gasket was the problem (plus changing the gasket is cheap and it was old anyway).

I pulled the old gasket off (no tools required).
I cleaned the track/slot that the gasket goes into, and the area around it from all the caked-on soap and gunk.
Cleaned off the door edge that seals with the gasket too.
I took the new gasket and folded it in half to find the middle, then started with the middle, putting it into the track (used the center door latch on the frame to know the middle on the washer).
I worked the gasket into the slot just with my fingers. I found that if I pinched the part that goes into the slot with my thumb/finger that helped get it deep into the slot without tools.
I worked around one side, slowly and carefully pushing it into the slot. Did the other side the same way - starting from the middle and working down to the end at the bottom of the washer. Checked the gasket to make sure it was all set in well.
There is an inch or so of the gasket left over at the bottom - I just bent that around the bend so it was not in the way.

UNIT WOULDN'T WORK. "CLEAN" LIGHT BLINKING

  • Customer: PAUL from ESTES PARK CO
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 34 of 48 people found this instruction helpful
The unit had power, but the controls would not work. The "Clean" light was blinking. I first replaced the control unit, no help. I then used the "Just Ask" and was told the problem was the heating element and/or the Hi-Temp thermostat. I replaced both those and used the re-set code pushing the "Hi-Temp/Air Dry, Hi-Temp/Air Dry" buttons. That did it. Easy parts to locate and replace. It took longer pulling the unit out and putting it back than it did to replace the parts.

dishwasher cut off during drying cycle

  • Customer: pauline from gloucester VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 30 people found this instruction helpful
After replacing the thermal fuse 5 times i noticed the new packaging came with a terminal block on then fuse harness. PLEASE USE THIS. It is a must, it supposedly is acting as some type of heat sink or something for added protection. Used the unit on all cycles now and works great. Just follow fuse instructions precisely. Hope it helps.

Borke the spinner off with dishes that were too tall. (Oops!)

  • Customer: Stephen from Leavenworth KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 22 of 22 people found this instruction helpful
1. Put a towel over the bottom of the machine. (In case you drop the screw... duh!)

2. Remove the top screw.

3. Replace the snap pin (pointy end DOWN.)

4. Snap the spinner in place.

5. Replace the screw. (Or go to the hardware store to replace the screw you dropped into the bottom of the dishwasher. Dashitall!)
All Instructions for the DU1055XTVS1
1-15 of 342