DU1055XTPS4 Whirlpool Dishwasher - Instructions

put new one in

cap was replaced

I watched the Video that was supplyed with the e-mail and when the part got here I new just what to do and it took maybe 15 min at the most. You saved me over $100.00 from what we had to pay once before for the same problem to a repair man. And now I know where to buy my parts for all my appliances when they fail and with KitchenAid it seems to be quite often.

Old gasket was broken in places and old. Installing the new one was easy- no tools required. Just pull out the old one and press in the new one. Washer still leaks because door does not close all the way- need to figure out how to get it to shut tight. Maybe the latch is loose or worn.

Followed the video and changed it out in 20 minutes which did not fix the problem entirely, but I went back to the list of symptoms and watched a video on exchanging the Chopper assembly. I disassembled the interior and found broken glass and wire and string restricting the rotational functions. No replacment was necssary here, but a good cleaning was in order. This made it run like new and the glasses came out shiny again. These step by step videos have even made me think about becoming an appliance repairman. LOL! This is about the 8th time I have had success with Part Select. I have had no failures. Thank you for giving away all the secrets. YOU DEFINITELY HAVE SAVED ME AND MY FAMILY TONS OF MONEY!

I would have torn something up had I not watched the video posted here first. The spring loaded chopper is a bit tricky to get in lined up properly to get the cover assembly back on. 30 minutes and several small finger tip cuts later, and the machine cleans like new.

Installed the rubber grommet and the door was fixed.Wish the product was made to lasts,second time in three years the part had to be replaced.

Removed old gasket by pulling it gently from one side to the other, cleaned track where gasket sits, replaced with new gasket by folding in half and beginning in center at top of dishwasher, using strike plate as center guide, working left side then right side, applying pressure with fingers to push new gasket in channel. I did replace the strike plate, but the one provided did not match the one I removed, therefore, was not working properly, so I inserted the old one back in and everything works fine.....no leaks. The instructional YOUTUBE videos on the internet were a big help to watch before beginning the removal and install. Couldn't have been easier and I'm sure I saved about $150 in repair person costs for time and labor only.

Ordered parts from Parts Select. Took 2 minutes to find and order. Received order following day! What service. Snapped old wheels off and new ones on....then replaced Spinner Assembly all within 15 minutes!

I removed front bottom cover on dishwasher. The drain pump is on right front side. Very easy to remove and to install a new pump.

Remove the 2 screws at top bracket to counter pull out dishwasher to unplug turn off water remove 2 access nuts for front panel removed water supply line remove 1 access nut for valve assembly then remove electrical connector. Reverse to install.

I followed the instructions from the web site-I.E. remove the star screws, remove the front panel remove the old dispencer, install the new dispencer.NOTE** I put the old dispencer in my garage vice and connected the solenoid using 2 alligator clips on an extention chord,and to my amazement- it opened and rinse aid fluid came out.I wish I would have had the knowledge to do that prior to buying the new part. I left the new part in and all seems to be working fine.

Well after trouble shooting several components , the fill valve, the check valve , the pump motor all it turned out to be is the supply line to the dishwasher. I had installed one of those lines with an anti flood check valve in the line. Thinking it was a smart idea so if I were not home it would keep from flooding my basement etc. even when you remove the line and run it into a bucket you still get flow. But unknown to myself a majority of your appliances do not work well with these lines because when the solenoid opens it causes a surge and the check valve tries to restrict the flow. After soapy of these surges the valve sticks . When I replaced the line with a standard supply line it solved the problem. So for about $15.00 you could save yourself a lot of headaches and money by replacing that first. I'm not saying it will be the solution but start there first even if your getting water flow through that line. By the way the manufacturer of those lines at least the one I bought less than 5 montages ago do not mention that on their package and by the time you come to that conclusion you may have spent a lot of money trying to fix your machine. I had three techs that couldn't figure it out. Also the machine I have is a kitchen aid but its a common problem on a lot of brands including washing machines for clothes.

Replaced locking roller. It took just a few minutes.

Only needed a screwdriver, removed screw and old part and simply reinstalled new part, in about 2 minutes.