DU1014XTXB1 Whirlpool Dishwasher - Instructions

The video is very helpful for replacing the Chopper Assembly. For the Impeller, reference the video for replacing the motor: http://youtu.be/pAKz1gMUWDA But once you have the motor removed and you identify the impeller, you need to insert a tool into the back of the motor to hold the impeller still from the back while you unscrew it in the front (I used a small wrench, a thin screwdriver would be ok too). Then, just screw on the new piece and follow the rest of the video to put everything back together again. Nothing this stay-at-home mom couldn't handle while the kids watched a tv show.

removed old basket, replaced with new one.

After attempting to change the "high limit switch" to no avail, I researched further and found that doing a reset/reboot cured the problem.The instructions for the high limit thermostat were a bit off, as there was no screw to remove, only a spring like bracket that I did not try to figure out. The work area is so tight if the dishwasher is not removed and tilted that I thought it best to look for alternatives prior to pulling it out and disconnecting power and water. So ... voila, it's fixed with a reset only. Reset is accomplished by pushing two buttons 5 times. "high Temp Scrub then Heat Dry, high temp scrub then heat dry etc, until you click them both 5 times.It will go through cycles for a few minutes, then after done, run the dishwasher as normal and test if fixed. There are a few different ways to do it depending on the model.

I had to pull the dishwasher out from the cabinets about 12" in order to pull the old seal off. Installing the new seal was quite easy, since there is no adhesive necessary. Start at the top center of the replacement seal and snap the groove of the seal which is hard plastic, into the mating parts of the tub and the tub trim. Its a little hard to explain, but pay attention to how the original seal (W10179427) was installed.

repairman replaced the valve inlet; first website tried to tell me I needed a new pump, but repairman said it would be some type of valve; service rep on phone very helpful,I ordered the correct part,except for having to lay on the floor, he repaired it easily; part came within 24 hours. Worked immediately. No additional tubes or parts needed.

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

Removed both baskets. Then removed 1 Phillips screw for upper rack water supply. Unscrew lower washer arm. Twist lower water supply clockwise to disengage from upper piece and from retainers. Remove 4 torx head screws and remove strainer assy. Remove 1 torx head screw from chopper cover and pull out chopper cover.. Pulled up on chopper screen and removed all broken pieces. Pulled on chopper itself to load the spring and put chopper in place. Make sure it goes in outer most slot. Reinstall in reverse order. Works perfectly.

Took lower impeller off and cleaned. Replaced the little plastic piece and voile - good as new! Was ready to buy a new dishwasher but thought we would try this first. Working as good as new. What a savings eh? Thank you part select for your great service!

Installed brackets

We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.

Remove power to the machine. My particular installation did not require physically removing water and drain lines. Remove the dishwasher from the cavity. Put a towel or two down on the floor. Lay the washer on its face on the towels and this orients the motor in the up position on the bottom of the washer. CAREFULLY unplug the motor wiring harness but if possible, leave the heating element connection in place as spade connectors tend to lose their grip with multiple engagements. Remove the single bolt located between the motor and stainless bottom of the cavity that locks the motor in place. Leave it in the cardboard shield, that really helps in reinstalling it. CCW rotation of the motor disengages it from its housing. Work the motor straight up and out of the housing. This was the most difficult part of the entire process due to the metal housing not quite clearing the plastic pump housing where they mate, but its do-able. Nothing should have to be forced. Now you have the motor in hand. Be very attentive how and what order you disassemble. Remove the back of the motor housing to block the armature to remove the impeller. DO NOT NICK THE FIELD WIRING IN THE MOTOR. I believe the threads were left hand but I don't remember the rotation. They do tighten in the direction of the motor rotation though. Carefully pry the seal out of the pump housing with many short lifts as to not mar the housing itself. Added a little dishwashing detergent on the outside of the new seal and carefully pushed it into place with the end of my screwdriver. Don't cut yourself on the metal insert in the center of the seal.Reassemble the impeller to the shaft WITH the spacer that comes with the new impeller kit. Make sure the impeller is tightened down completely to the end of the threads to insure proper clearances when reassembled. Don't force or over tighten. You'll feel a positive stop. Reassemble the motor to the housing Lubricate the housing o ring seal on the outside with a VERY small amount of dishwashing liquid lest you create a suds factory on startup. Replace the holding bolt on the pump housing. Reconnect the motor leads and heater element if removed. Stand the washer back up. There will probably be water around the door area from the pump when the machine is returned to the upright position. Reconnect lines and check under the pump housing for leaks while in operation being careful not to get into moving parts or electrical connections. Good luck.

Due to the posts on this site, I took the advise of replacing the chopper assy. Old chopper did not look bad and seemed to function. Apparently I was wrong. After new chopper was installed, dishwasher worked fine.