DLSR483GE0CC General Electric Dryer - Instructions

The clothes would get caught where the drum slide should be (it was almost totally worn down) and would leave black marks. I watched Parts Select youtube video. Bought the parts needed from Parts Select. They arrived within a couple of days. I replaced the 2 drum slides and no more getting caught. Took about 20 minutes.

The Felt Drum Seal actually fell apart and got pulled into the area between the drum and the front drum bearing. I pulled out the seal, looked at ps.com's schematics, and ordered the drum seal and the 4 bearing slides. I figured I might as well replace the slides while the top and front of the dryer were off. Previous postings and the video were very helpful. I did take off the dryer door (remove 2 screws and loosen 2 screws to take it off) to make it easier to remove the dryer front. Do watch the wires to the door switch and the light: gently move the dryer front just far enough from the dryer to get behind it. Install felt seal and make sure it is completely in the guides with flat side against the dryer front. Install bearing slides exactly the same way as the old ones: they just clip into place. Have a brush or vacuum handy to clean the channel from the dryer lint trap. Mine was full of lint. You will have to reach in and raise the dryer drum slightly to put it back on top of the front bearing as you reinstall the dryer front. Very easy repair for anyone with a small amount of mechanical ability. I estimate I saved the cost of a $150 service call ($75 to show up and minimum 1-hour of labor at $75 in my area). Thanks parts.com!

Pretty easy fix with the removal of 4 screws, disconnected front panel , disconnected wires on front panel, removed top panel, once all panels were removed pulled out drum, while removing belt, removed damaged rear drum bearing held in place by 3 screws replaced new rear drum bearing, Removed light bulb, popped out plastic front drum bearing replaced 4 new drum slides on new front bearing popped it back in place, removed old felt strip, replaced with new felt strip, put it all back together front panel first, removed four screws on control panel to make the top panel easier to replace, and fired it up, it was as quiet as new, great videos that made the job allot easier and saved a ton of money to boot. Thank you for your quick delivery time as well..

I removed the drum from the dryer (the instructional videos on this site showed me exactly what to expect) and it got easier from there. The old O-ring on the rear bearing had broken and the sleeve was moderately worn, but both were easily slipped off by hand and replaced. As for the front bearing, the new slide plates inserted onto the edge of the new bearing plate easily. The old front bearing was badly worn, and except for one, all of the slide plates were worn to nothing. This was apparently the cause of the terrible squeaking noise. After removing the light buld and applying a little pressure, the old bearing popped out and the new one replaced it just as easily. You must remember that there are 4 slide plates that mount to this bearing and they are SOLD SEPERATELY! You have to buy 2 black ones and 2 white ones and each is sold individually. Once replaced, the dryer worked good as new! While I had the dryer apart, I removed all of the built-up lint from the exhaust line and the interior of the unit with my hands and a shop-vac. My dryer now runs squeak free and my drying times have decreased substantially due to the cleanout of debris. I highly suggest you watch the instructional videos on this site, they are extremely accurate.

The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.

first, I watched the helpful videos. I then removed the screws that are located inside the door and screws from for top panel to remove front and top panel. When I opened the front panel I saw that the front drum bearing was half destroyed from the years of drum rubbing. I Replace front drum bearing and slides and now dryer sounds like a brand new quiet dryer.

First up, remove the two screws that hold the top cover on - you can see them when you open the front door. Once those are out, close the front door and pull off the top cover. Remove two more screws (one on each side) that hold the front panel in place, then undo the clips and move the front off to the side - you don't need to unplug the harness for the door, it's long enough to move out of the way. I had to remove the drum next - it's held in place by 3 Torx head screws on the rear wall of the drum. Once the screws are out, you can slide the drum forward and off the belt so you have enough room to replace the igniter. The ignitor is down below on the right side, held in place with one screw, under a gray ceramic piece that (I assume) directs the flame - that part is held in place with two screws. Once that is out, you can undo the 2-prong connector, and use a short Philips screwdriver to remove the igniter. Be careful installing the new one, as the ceramic tip is fragile. Reassembly wasn't too bad, but it really helped to have an extra pair of hands to start the screws that hold the drum in place on the rear bearing. Since everything was apart, I also replace the drum sliders - this particular dryer uses 4 of them, and it spins nice and quiet again!

The repair went just as the self help video showed on your web site. Since I was replacing front air duct assembly, and had unit disassembled I figured on replacing upper portion, bearing slides (as recommended) and lint basket. Now it as good as new. Thanks for the help!

I watched the installation video a of couple of times and followed the instructions. Two screws under the dryer door then the top comes off. Then two screws hold the front on come out. Unplugged the two wires to the switch. Removed the duct assembly. Cleaned up the door and snapped in the new duct assembly. Re-installed the door and then the top. Everything was easy - just like in the video.

Reviewed problems with the dryer on line and ordered the parts. The only problem is that it takes two types of slide bearings which I did not order correctly. The video was great and had no problem installing the parts.

We watched the video of how to take the dryer apart and how to install the thermostat...after watching the video it was pretty easy

The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.

I went online to watch videos of how to take a dryer apart. I shut off the gas line and unplugged the power cord and cut the zip ties holding the exhaust tube tight on the exhaust. I took the dryer apart and inspected parts for wear. When I had the drum out and belt off I felt that I had seen all the worn parts. I spent a half hour cleaning the inside of the dryer. I carefully used compressed air, a small vacuum, and paper towels. I cleaned the exhaust vent in my home, and bought a new vent tube as the old tube was worn. I ordered the bearings, bushings, slides, belt, and felt seal that I could see were worn. I also ordered the plastic frame that holds the sliders as it was worn and broken. I used electrical tape to cover a wire for the inside lamp that was worn partially bare. You should stop using your dryer at the first sign of odd noise, take it apart, and install new parts. With the new parts and full cleaning, the unit runs like new. Very quiet. Just be super careful when you install the drum back in and place the belt correctly. You need to look at where the belt goes, memorize that, then put your arms in and install the belt without being able to see anything because of the tight area. Be careful not to cut your arms on the sharp metal body. You could put tape over any exposed edges to make your work safer and less worrisome. Try out the dryer when you are done with the assembly to see if it works without hooking up the gas. It will run smooth, and a little more dirt will come out. Then hook up the exhaust carefully, then the gas. Lastly, try it out. It should work like new, push lots of hot air out the exhaust. When you are done you will feel good and may just decide to paint the laundry room or put up new shelves like I did.

Took the knob and clip off the dryer and stuck the knew knob on!

Very easy to remove the front and top with a total of 4 screws as per the video. Removing the old piece was easy. The only hang up was putting the new piece on and it wasn't fitting snug. I then realized there was a lip that should sit around the dryer door open. Once I did that it fit perfect and was a matter of putting the screws back.