Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas dryer heat would not come on
Unplugged dryer, opened lower panel. Loosened the bolt that holds igniter assembly to gas unit and removed old igniter. Put new igniter in the pinch clamp then (being VERY careful so as not to crack new part) replaced igniter assembly and tightened its bolt firmly. Voilà, ignition!
pried old switch assembly from front of machine with screw driver. removed 2 electrical connections. shorted terminals to verify problem. inserted wiring terminals to new switch. verified operation and then pushed switch assembly into machine opening.
1. remove the access door , bottom left side 2. unplug the power cord and shut the gas valve off, next to the union fitting 3. unplug the electrical connections from the gas valves and igniter. 4. open the union with the wrench, right hand thread 5. remove the two nut driver screws on the burner lip 6. remove the burner and carefully spread the igniter fingers and remove the igniter 7. check the igniter, make sure it is the problem. 8. install the new igniter and carefully insert the burner into position. 9. reverse the disassembly , turn on the gas valve and check for leaks with soap bubbles. if you have a leak, shut off the gas valve and repair it or leave the gas valve off and call a repairman. 10. plug in the power and turn on the dryer the igniter should glow white hot and the burner should light. 11. if the dryer does not work you have other problems or you did not plug the electrical connections into the correct places, 12. call the repairman or buy a new dryer
I checked the power (OK) and removed the four screws that held the timer/controls (upper panels) cover. This revealed a schematic for the dryer that enabled me to determine the door swich was probably the culprit. I pried out the old switch and, sure enough, it was always open (checked with multi-meter). I found the replacement switch easily using the dryer model number and "door switch" search string. Ordered Sunday night, the part came on Tuesday and took 2 minutes to install (no tools needed).
Dryer worked, but there was no heat to dry the load.
Removed from lower panel. Just popped it open with a screw driver. Unplugged dryer and shut off gas by the gas shut-off valve. Loacated the gas igniter element and removed it by pulling up. It is only healed in place by a metel like a clothes pin. Using caution slid new unit down and into the pinching device. Plugged in power cord and the gas. Turned the unit on and it worked !!! This was worth the try. Better than buying a new dryer with the economy the way it is now.
It was very easy. Pop out old, connect new wires and done! Can't say enough as to how fast and easy getting the part from this company was. Ordered the part later in the day one night and on the second day the part was there. Outstanding service.
Unplugged the power cord, turned off the gas. Then I closed the gas valve feeding the gas igniter assembly. I disconnected the gas pipe from the gas igniter assmb. Then I removed the two screws holding the assmb. on to the front of dryer. From this point the assmb. can be lifted off a supporting bracket. Three cables must be removed in order to remove the assmb. from the dryer. The gas igniter measured very high resistance and actually fell apart. Reassemble in the opposite order as above. Parts diagrams on Partselect.com were invaluable.
shut off gas supply, pulled elect plug on dryer, removed gas supply assembly ( 4 screws and 3 plugs ). found broken gas igniter cleaned with air compressor. replaced gas igniter.
Watched the video, however my unit was 38 yrs old, the video was very very helpful but not exactly for my unit. If you have the time to repair yourself, and your mechanical go for it. its really not that difficult. I also changed the rear bearing sleeve that was worn out.The video was worth watching. I'm sure I saved a few dollars.
1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed
1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed
Unplug the dryer, turn off the gas. Opened the lower front door panel. She disconnected the gas pipe from the igniter assembly. Then She removed the two screws holding the assmb. Then she removed the wire from the front of the assmb. and the white and black wire from the back of the unit. remove the old igniter put in the new one put it back together.
Unplugged dryer, disconnected gas from igniter sleeve and removed sleeve (AFTER you unplug all wires). Replace the igniter "very carefully". It is as fragile as bare pencil lead. Replace the igniter sleeve. Beats the snot out of buying a new dryer. Thank you for having the parts.
