DLL2650RBLWW Hotpoint Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer leaving marks on clothes. Clothes were getting caught between drum and outside ring. Worn slides.
Remove top panel and front panel. 12 Screws. Be sure to vacuum entire inside of cabinet free of lint.
Parts Used:
-
E. Thomas from REDONDO BEACH, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old lint filter had a hole in the screen.
-
Dennis from CLOVER, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No flame. Igniter came on but no gas.
Opened up dryer for access to all components and tested. All checked good. Put back together and tested and igniter came on but no flame. Purchased two new coils and tested again. No flame. Purchased complete valve assembly and replaced old one. Tested again and viola, success! TY PartSelect for exact replacement part.
Parts Used:
-
Gary from CHRISMAN, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt out bulb
-
Jeffry from ROCKVILLE, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Parts Used:
-
Shelly from MURFREESBORO, TN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Parts Used:
-
Peter from LEOMINSTER, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced dyer belt
First unplug dryer... very important. You have to identify the appropriate size socket wrench and locate all necessary screws to remove top panel of dryer and front panel. Locate belt drive. Remove old belt , replacing it with new belt attaching belt to dryer drum . Remove back panel of dryer to better reach and adjust belt onto tension wheels. Put dyer back together. YouTube gives you an idea of how to properly change a belt on dryer
Parts Used:
-
Vernon from BALTIMORE, MD
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Parts Used:
-
Timothy from Rochester, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas igniter: broken
Unplugged dryer, disconnected gas from igniter sleeve and removed sleeve (AFTER you unplug all wires). Replace the igniter "very carefully". It is as fragile as bare pencil lead. Replace the igniter sleeve. Beats the snot out of buying a new dryer. Thank you for having the parts.
Parts Used:
-
Chrislee from Highlands, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set, Wrench (Adjustable)
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint filter has never been replaced.
This wan't a repair. It was simply a part replacement for a part that was easily accessable. I was more pleased at the fact that I could find the part considering how old the dryer is.
Parts Used:
-
Marcus from Morrisivlle, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint filter was tearing up
Easy as steps 1 & 2, remove old filter & replace w/ new.
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..
Parts Used:
-
J. from Luverne, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb blew out inside the dryer
-
Donna from Vista, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas igniter had quit working
My Daughter did it for me .
Unplug the dryer, turn off the gas. Opened the lower front door panel. She disconnected the gas pipe from the igniter assembly. Then She removed the two screws holding the assmb. Then she removed the wire from the front of the assmb. and the white and black wire from the back of the unit. remove the old igniter put in the new one put it back together.
Unplug the dryer, turn off the gas. Opened the lower front door panel. She disconnected the gas pipe from the igniter assembly. Then She removed the two screws holding the assmb. Then she removed the wire from the front of the assmb. and the white and black wire from the back of the unit. remove the old igniter put in the new one put it back together.
Parts Used:
-
Robert L from St Louis, MO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Wrench (Adjustable)
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt broke
Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.
Parts Used:
-
Robert from Patchogue, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn ratty old lint filter
Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!
Parts Used:
-
keith from albert lea, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!