DLG7 LG - Instructions

Removed top of dryer
I carefully removed wires from back of control panel
Removed control panel
Most of screws hold cabinet together
Unhook wire from light on door and sensor on the front panel.
Remove the front door and panel together
I changed both front rollers on front panel
If you have to change rear rollers lift tub up by belt
Remove screws on back of dryer that will let you lift out inside rear panel that holds the rear rollers
Change rollers and just revearse procedure to put back together

Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.

The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.

To use the new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.

Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!

My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.

Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.

I did not do the repair I hired the propane company to do it . It was too difficult for me.they removed top & front of dryer .removed & replaced gas orfice reinstall all parts that were removed. Install and test dryer IT cost me $91.59 for labor & $24.65 for the part & shipping.If the dryer had a side access near the gas valve it could have saved me the cost of labor. I could have done it myself.

Opening the dryer door on the vertical axis rather than the horizontal axis, I unscrewed the three obvious screws. These screws are clearly visible when viewed from eye level. The broken hinge came off in two pieces, but presented no difficulty. I inspected the area around the hinge for auxiliary damage. There was none, but I did notice a wisp of cotton candy stuck in the lint trap. This was odd as I had not had cotton candy of any kind in my home or near my dryer ever. I did hear the faint sound of calliope music-I assumed this to be from an ice cream van that frequents the neighborhood-but failed to detect the tell-tale doppler effect of a moving vehicle. Disturbed, but determined to finish my task I removed the new part from the packaging and checked the fit. It fit perfectly. NOTE: Retain the screws from the hinge you remove, as the replacement hinge does not come with screws. I looked down to where my screws lay and saw the bulbous oversized toe of large red shoe. There was a star on the tip, painted in blue and yellow. I looked up from the shoe to see it attached to an ankle with a frilled cuff and up from there a baggy pair of pantaloons. At this point I realized that circuses now being illegal in this country, I clearly had a rogue clown on my hands. Sitting as I was I was not able to quickly get up, and in the confines of my washroom I had nowhere to run anyway. I had to think fast. I could smell the stale popcorn on the clown's breath as he leaned over, I reached for anything I could, grabbing up a pet cleaning vacuum hose. The clown just snorted and said, "You want a Phillip's head for that." The clown was right, of course. I installed the screws, checked that the door worked, and then the clown and I went for churros.

Watched a You Tube video

One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.

Pull off the top and front of the dryer and reached in and replaced the part it was easy. Had to clean all the dryer out real good with from the lint

Pull out the worn out dryer filter and replaced it with a new filter that I purchased through Partselect.com.
It fit perfectly.

I took the old lint filter out and put it in the garbage. I the put the new lint filter in the dryer. Problem solved

Take old one out and slide new filter in.

Put the new lint filter in and it was completed

Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. But that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.

Replaced idle pulley wheel, worn drum belt and all 4 rollers (1 frozen) due to dryer age. Site video re general disassembly/re-assembly easily adapted to this model and very helpful with exception of replacement of drum rollers. New rollers received (AGM75510755) were pre-mounted on included shafts. This required removal of existing roller shafts to replace with new shaft/roller units. Site video shows placing a new roller on existing shafts after removing a plastic retaining clip. New roller/shaft assembly is a better option and fortunately I did not order extra retainer clips! Rear drum roller shafts have small carved out space to fit a box end wrench to remove shaft nut. Watch out for sharp edges on internal steel parts!

Part showed up in 2 days and repair took 2 min. Very easy. Thank you!!

Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.