Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLEX2801L > Parts

DLEX2801L (ARBEEUS) LG Dryer - Parts

All parts for the LG Dryer DLEX2801L

Below is a list of all parts for the LG Dryer DLEX2801L - Residential DRYER. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the DLEX2801L
1-14 of 85
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$29.93

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$51.28

Lint Filter

The lint filter is designed for use in your dryer. The function of the lint filter is to catch lint and debris during the operation of the dryer. If your old lint filter is old or damaged, or there are marks left on your clothes at the end of the dry cycle, you will need to replace it with this part. This part is approximately 12 inches in width by 11 inches in height. Many of our customers have rated this repair as very easy. To complete the repair, simply remove the old filter, clean up any remaining lint and debris, and install the new filter.

$23.64

Thermal Fuse

This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the ...

$6.92

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove the front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

$3.79

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside you...

$23.64

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

$25.39

Cover,Guide

$16.15

Guide,Filter

$133.60

Heating Element Assembly

They are all strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The h...

$4.40

Leg

$24.26

Thermostat Assembly

$4.40

Clamp

$215.21

Tub Drum Assembly

This part rotates to circulate air through the clothes.

$143.61

Drive Motor

This motor works with the belt to drive your dryer's drum.

All Parts for the DLEX2801L
1-14 of 85