Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DHDSR46EE1WW > Instructions

DHDSR46EE1WW General Electric Dryer - Instructions

All installation instructions for DHDSR46EE1WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DHDSR46EE1WW
31-45 of 742
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noise from the drum in the dryer

  • Customer: William from Blue Springs, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 38 of 66 people found this instruction helpful
The weight of the front section of the drum in the dryer rides on 4 slim pieces of plastic. remove the screws that hold down the top of the dryer are in the front door at the top at each corner. remove the top, then remove 2 screws that hold down the front of the control panel to the cabinet at the base. remove the 2 screws at the of the front corners of the cabinet to separate the front door section from the rest of the dryer.Watch out for the wires the connect the door to the rest of the dryer. if you replace the bearing at the back of the dryer you need to take two screws out at the base of the cabinet one from each corner to let the sides of the cabinet to spread out and let the drum pass though the front of the dryer cabinet. the belt has to come off the motor by lifting it up an sticking your hand in under the drum and working it off the end of the motor. replaced the parts ad the dryer works like new.

making noise

  • Customer: Lissa from Redlands, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 36 of 60 people found this instruction helpful
Replaced idler pulley and belt very simple

Dryer took a long time to dry clothes

  • Customer: Darrell from Springdale, AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 34 of 56 people found this instruction helpful
First I removed the removed the screws that held the top on the dryer. Next I removed the screws that held the controls on from the back. I then removed screws that held the left side in place and removed the drum by first removing the drive belt.
The heating element unit was removed by removing four screws and the wiring harnes. I reversed the procedure to install the heating unit and put the machine back together.

dryer would not heat

  • Customer: Mike from Simpsonville, SC
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 36 of 63 people found this instruction helpful
The heating element was broken.

Broken knobs

  • Customer: Ray from South Pasadena, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 31 of 51 people found this instruction helpful
Actually putting on a knob is self-explanatory. But wanted to say your company had the best price and reaction (delivery time). Great job by PartSelect!

Dryer squeaked when running

  • Customer: Mark from Garrett, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 25 of 34 people found this instruction helpful
Everything is cleaned as it is removed.

Remove the two screws holding the top down.
Disconnect two wires from door switch.
Remove the two hex screws holding the front on.
Remove the 4 screws holding the access panel on the back and disengage idler pulley to loosen the belt.
Remove the drum.
Label the wires then remove the heating element.
Check orientation of ground strap before disassembling rear bearing.
Remove four screws holding rear bearing to back of heating element.
Install rear bearing and ground strap on to heating element.
Reinstall heating element.
Reconnect wires.

Most Important : Get help putting parts back on drum! I didn't and that's why it took over 2 hours.
I will describe how I did it.

Unscrew bearing from inside of drum.
Wrap screwdriver with tape to a little larger than the screw hole.
Use small screwdriver to line up the drum, shim and deflector.
Don't forget the brass shim. It wasn't on the parts diagram.
Start two screws don't tighten them yet.
Remove Screwdriver and start third screw. Tighten all three down.
Put belt on drum.
Install drum and belt.
Reverse disassembly.
When putting the front on make sure drum rests in the felt.

I rated this a bit difficult because I did it myself. With help this is a fairly easy repair.

Loud squeaking. Speaking in demon tongues.

  • Customer: nathan from los angeles, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 21 of 27 people found this instruction helpful
Pulled the front of the dyer off, snapped old bearing off, snapped new drum bearing in, affixed 2 new slides and 2 new other widgets (5 pieces total). Vacuumed/cleaned out various bits and pieces before i closed her up.

No squeaking.

Called a priest, but he died. Now i just do whatever the demon says, but i do it with quietly dried clothes.

Deflector was covered in burnt something.

  • Customer: Richard from San Antonio, FL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 22 of 32 people found this instruction helpful
Deflector has 3 bolts attaching it. They require a star wrench. Had to purchase same to do the repair. Removed the bolts(they are sheet metal type screws(bolts). Installed the deflector and started dryer. Loud rubbing sound noted. Shut off and checked the drum and noted it was not running concentrically. Removed deflector and the found the 3 screws actually retained the drum to drive. Had to make alignment pins to allow proper alignment of the drive, drum, and deflector. Once the pins were used during installation of the deflector everything worked correctly. Turned on dryer and it operated normally.
Had I had the proper tools the repair would probably have taken 30 minutes or less.

Drum Bearing slides were worn and broken, dryer made high-pitched noise.

  • Customer: Gary from Glenmoore, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 16 people found this instruction helpful
First, let me say that my repairman said the bearing and slides would cost between $150-200, and the total repair would be pushing $400, so we should just get a new dryer. Well, the total cost for the parts was less than $50.

The installation was easy.
1. Remove the two bottom screws of the door hinges, loosen the two top screws, and remove the door.
2. Unscrew the two screws, under the upper lip of the door opening, that secure the front panel to the top panel.
3. Pull the front of the top panel up, and then pull the panel off.
4. Remove the bulb from the front panel.
5. Unscrew the two screws, from inside the dryer, that secure the front panel to the frame.
6. Pull the front panel away from the drum and frame. Had to lift the drum slightly to do this. The electrical connection wire was still attached to the front panel.
7. Slide off the old drum bearing from the inside of the front panel.
8. Insert 4 new slides onto the new bearing.
9. Slide the new bearing onto the rim of the opening in the front panel.
10. Reset the front panel back into the slots at the bottom front of the frame, with the bearing fitting into the drum. Again, had to lift the drum slightly to do this, and make sure the wire was not caught between the front panel and frame.
11. Re-secured the front panel to the frame with the two screws.
12. Replaced the bulb in the front panel.
13. Replaced the top, and re-secured it with the two screws.
13. Put the door back on.
Quiet dryer once again! And saved the $800, including installation, a new gas dryer would have cost us!

Dryer squeeked badly when running.

  • Customer: Craig from Castle Rock, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 24 of 41 people found this instruction helpful
I've always heard it was a simple job to replace the belt and that would solve the problem. I'd defer to others online when they suggest to replace the rear bearing - they are totally right about that suggestion. My bearing basically fell apart in my hands. Not sure if I needed a belt or not, but it's worth replacing while you are tearing the thing apart. It took way longer to tear apart than to put back together. The parts and prices from PartsSelect were perfect. The parts were received in 4 business days as they said and were perfect replacement parts.

The dryer began squeeking very loudly progressively getting worse

  • Customer: Michael from Sioux City, IA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 22 of 35 people found this instruction helpful
A very easy fix. Opening the front door to the dryer locate two chrome phillips head screws in the upper part of the door opening which hold on the top of the dryer. (I think in the older dryers the top simply was held on with keepers and you could simply pry it off. Not the case here)Lifting up on the front of the top it comes away from the back control panel. I would recommed that the control panel be removed as it is necessary to remove it to put the dryer top back on due to three clips that wont allow you to put the top back down with the control panel in place. It takes a star wrence to remove it. Once the top is off ther are two phillips screws holding the front of the dryer on (one on each side) remove them and the whole fron lifts up and off. The drum rides on a plastic schroud attached to the dryer inside front. Mine was so worn it required the purchase of the entire assembly which comes in two parts. The upper part had worn away so badly the drum was riding on the metal causing the noise. I ordered both the upper and lower assembly and both just simply snap off and the new ones snap right back on. No tools. I was a bit dissapointed as I assumed that the felt which is located in the lower assembly would come with the new part however it did not nor did some plastic tabs which the drum rides on in the upper assembly comes with the replacement part. It takes four of those tabs so order appropriately. Went back together easily and the whole job was done in about 40 minutes.

only orderd two sliders needed four

  • Customer: William from Leesburg, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 20 of 30 people found this instruction helpful
easy no problem

Dryer making squeaking noise when operating

  • Customer: Michael from Clay, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 21 of 33 people found this instruction helpful
First I had to remove the top by taking out the two screws inside the door. Then I removed the front by taking out the two screws holding it from the inside. I needed to remove the drum and to the the belt off, I removed the left side. It has several screws down the back, two on the bottom and two in the front. I removed the belt and drum. I took out the old sleeve bearing. Part of it was broken off into the hole it goes into. I then had to remove the plate that holds the heating element. Once that was done, I put the new bearing on and replaced the drum slides on the from section. Then I reversed the process to reassemble. Not too bad.

dryer was cutting off completely.

  • Customer: Stephen from Mechanicsville, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 20 of 31 people found this instruction helpful
The problem was intermittent. It only happened when the unit was first started. After it was restarted it usually worked until the load was dry. I looked at the schematics and saw that only the hi-temp therostat and the motor overload could stop the dryer completely. I put my volt meter on the hi-temp thermostat and ran the dryer. When the dryer stopped I realized the hi-temp therm. was tripping. I read the web site help for this symptom and the suggestion was the bias therm.
I replaced it and the unit worked.

Faint Squeek after dryer had been running for an hour or so

  • Customer: Stephanie from Cicero, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 22 of 37 people found this instruction helpful
It makes it real easy if you have two people!! Put the dryer on it back--You'll need to protect the floor and the warm air exhaust of the dryer.
Remove the two screws that secure the top--they are located on the inside upper portion of where the door seats on the front panel. Remove the top
Remove the front by removing two screws near the top--one on each side
Remove the belt from the idler pulley--note how it comes off
Lift drum out of dryer
Use the torx bit to remove the bearing
If you got the kit it comes w/ the bearing housing--you'll need to disconnect a couple of the wiring harnesses holding the heater--replace the bearing housing
This is the perfect time to remove all dust bunnies
Re-install everything in reverse order
All Instructions for the DHDSR46EE1WW
31-45 of 742