Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DGBD2432KB1

DGBD2432KB1 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for DGBD2432KB1

If you know the dishwasher repair part you need, you can browse the list of all parts on the DGBD2432KB1, or you can search by name or part description. You can also find your part by where it is located on the DGBD2432KB1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for DGBD2432KB1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.00

Tub Gasket - Gray

The gasket provides a waterproof seal between the tub and the door.

Order within the next 8 hrs and your part ships today!
$12.93

Upper Spray Arm

This part is located on the top of the tub.

Order within the next 8 hrs and your part ships today!
$25.18

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

Order within the next 8 hrs and your part ships today!
$26.76

Lower Spray Arm with Shields

Water is supplied to this part via the pump assembly.

Order within the next 8 hrs and your part ships today!
$6.37

Heating Element Brass Nut

This nut is sold individually. It is used to install the heating element.

Order within the next 8 hrs and your part ships today!
$19.77

HOSE

The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage. Size: 7.5 feet long

Order within the next 8 hrs and your part ships today!
$17.66

Splash Shield Kit

This is installed at the bottom corners of the door seal.

Order within the next 8 hrs and your part ships today!
$18.47

Door Spring

Sold Individually.

Order within the next 8 hrs and your part ships today!
$72.90

Upper Rack Assembly - T3 PRO

This is the complete upper rack and the wash arm.

Order within the next 8 hrs and your part ships today!
$53.87

Drain Pump -120V 60Hz

The drain pump ejects the water from the dishwasher.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The spray arm would fall off during the washing cycle.

  • Customer: Roy from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 607 of 614 people found this instruction helpful
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the a... read more

Bottom Door Seal fell apart and started leaking.

  • Customer: Scott from Flowood, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 160 of 179 people found this instruction helpful
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the doo... read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 127 of 139 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more