All Installation Instructions for Maytag Dryer DE19CD

Dryer noisy

I basically just followed the excellent instructions in the PartSelect video; I highly recommend it. Be careful of other sites, I had one site that told me to take off the top of the dryer somehow, which would have been MUCH harder. Be sure to lay down a drop cloth, it is dirty inside these things.

Parts Used:

Tumbler and Motor Belt

Michael from Lawrenceville, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Dryer door would not close

Sooooooo easy! Ordered the part on-line and it arrived the very next day! Watched the 'how to' video on-line and the fix was a breeze. Bought my Maytag dryer back in 1989 and this is the only problem it's had. For a repair just under $5.00 plus shipping? I'll take it!

Parts Used:

Door Latch Kit

James from Tabernacle, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

grinding on start and through out running then sounds grind after dryer has stop

Followed the video to the tee really easy. But I have been in the dryer before teflon rub guides and belt.Take the front off, then the drum bracket four screws, open the blower wheel cover, remove the locking clip the wheel just slid off then, put it back together everything lined up just fine. then say to your wife listen to the dryer you can't hear! Works great.

Parts Used:

Blower Wheel with Clamp

Neal from Hutchinson, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

rollers worn ,rumbling when drum turned

removed front cover and rear access panel took belt off tensioner removed front drum support removed drum replaced two rollers by removing snap rings and put it back together in reverse... The maytag repair man is still lonely

Parts Used:

Drum Support Roller Kit

scott from auburn, MA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Loud squeak coming from rollers

The online video was the extremely helpful in aiding me in the repair. Thank you so much for posting it. Couldn't have done it without it.

Parts Used:

Roller Shaft

Drum Support Roller Kit

David from Chino, CA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

noisy and drum wobbling

Installing the Front Glide Kits was straight forward if you watch the video. The guides resolved a part of my problem, but I discovered the Blower Wheel was cracked and out of round. replaced it and poof its fixed!

Parts Used:

Front Glide Kit

Jeffery from West Linn, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

New rollers replaced

Followed the guidance on video.

Parts Used:

Drum Roller Shaft Washer

Drum Support Roller Kit

Retaining Ring

David from Helena, MT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Door catch broken.

I pried out the old one slightly and grabbed it with pliers. Quite possibly the metal catch dropped into the door section, but no problem. I pushed the new one into place with the side of the pliers. Probably 3 minutes time.

Parts Used:

Door Latch Kit

Byron from Los Angeles, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

dryer started making nocking noise

found info describing the nocking noise found parts to fix it watched video on how to do the repair The step by step instructions made the job so easy We saved over 150.00 in doing the job ourselves. thank you I am amazed at how simple this turned ou to be.

Parts Used:

Front Glide Kit

Myra from Dillon, SC
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Wrench set

Was this instruction helpful to you?

Thank you for voting!

Belt broke

Following video instructions, replaced the belt. Did it once before so this time it was easier. Two years ago I replaced the plastic fan as it was spinning on moter shaft making a loud noise. (The moulded plastic fan has a flat which slides on the motor shaft. The motor start up torque over time (15 + years)stripped the flat allowing the fan to spin on assembly.) The mistake I made was not replacing the belt when I had the machine apart to replace the fan.

Parts Used:

Tumbler and Motor Belt

John from Del Mar, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Rattling Noise

Replaced the Blower Wheel, the Idler Pulley Wheel, the belt and blower seal. Cleaned inside of the unit while I had it apart. Runs very quite. Very easy to do repairs.

Parts Used: