Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was making loud squeak
This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.
I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.
after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.
we heard the most deafening screech! when we investigated we found that the plastic part that the shaft rested in was worn, unevenly and the shaft end was scored. (we live in a house with 8 people so a fast fix was needed) I looked up the part on a sears site. when I checked the part avalibility I f
we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"
I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's. removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble. this should be available as a kit, and should include high temp grease to put in bearing bracket
