DBXR463ED2WW General Electric Dryer - Instructions

I grabbed the broken knob firmly and pulled it straight off. I took the new knob and pressed it firmly into place.

removed the old broken handle, and snapped the new one in place, total time; 10 seconds.

The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.

Snapped on the new on the new one. all done

Bought both the knob and metal insert clip. Turns out that the clip was unnecessary as the knob came with the clip. The repair was quite simple. Simply pull out the old knob and insert the new, taking care to align the D.

first, I watched the helpful videos. I then removed the screws that are located inside the door and screws from for top panel to remove front and top panel. When I opened the front panel I saw that the front drum bearing was half destroyed from the years of drum rubbing. I Replace front drum bearing and slides and now dryer sounds like a brand new quiet dryer.

The repair went just as the self help video showed on your web site. Since I was replacing front air duct assembly, and had unit disassembled I figured on replacing upper portion, bearing slides (as recommended) and lint basket. Now it as good as new. Thanks for the help!

I watched the installation video a of couple of times and followed the instructions. Two screws under the dryer door then the top comes off. Then two screws hold the front on come out. Unplugged the two wires to the switch. Removed the duct assembly. Cleaned up the door and snapped in the new duct assembly. Re-installed the door and then the top. Everything was easy - just like in the video.

Reviewed problems with the dryer on line and ordered the parts. The only problem is that it takes two types of slide bearings which I did not order correctly. The video was great and had no problem installing the parts.

We watched the video of how to take the dryer apart and how to install the thermostat...after watching the video it was pretty easy

The repair was extremely easy to do. The video was perfectly done and described everything one needed to do in very simplistic details.

I went online to watch videos of how to take a dryer apart. I shut off the gas line and unplugged the power cord and cut the zip ties holding the exhaust tube tight on the exhaust. I took the dryer apart and inspected parts for wear. When I had the drum out and belt off I felt that I had seen all the worn parts. I spent a half hour cleaning the inside of the dryer. I carefully used compressed air, a small vacuum, and paper towels. I cleaned the exhaust vent in my home, and bought a new vent tube as the old tube was worn. I ordered the bearings, bushings, slides, belt, and felt seal that I could see were worn. I also ordered the plastic frame that holds the sliders as it was worn and broken. I used electrical tape to cover a wire for the inside lamp that was worn partially bare. You should stop using your dryer at the first sign of odd noise, take it apart, and install new parts. With the new parts and full cleaning, the unit runs like new. Very quiet. Just be super careful when you install the drum back in and place the belt correctly. You need to look at where the belt goes, memorize that, then put your arms in and install the belt without being able to see anything because of the tight area. Be careful not to cut your arms on the sharp metal body. You could put tape over any exposed edges to make your work safer and less worrisome. Try out the dryer when you are done with the assembly to see if it works without hooking up the gas. It will run smooth, and a little more dirt will come out. Then hook up the exhaust carefully, then the gas. Lastly, try it out. It should work like new, push lots of hot air out the exhaust. When you are done you will feel good and may just decide to paint the laundry room or put up new shelves like I did.

Took the knob and clip off the dryer and stuck the knew knob on!

Very easy to remove the front and top with a total of 4 screws as per the video. Removing the old piece was easy. The only hang up was putting the new piece on and it wasn't fitting snug. I then realized there was a lip that should sit around the dryer door open. Once I did that it fit perfect and was a matter of putting the screws back.