CYG4000AWW Magic Chef Dryer - Instructions

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

I'm a 65-year-old woman with no prior appliance repair experience. I learned on the web that 30% of the time, the failure-to-heat problem is caused by the valve coil, and 30% of the time, it's the cycling thermostat. So I ordered both parts. I watched installation videos on the web. The valve coil was accessable through a front port on the dryer so I started there. I had to go buy a stubby screwdriver because access to the screws was limited. From there, it was easy to take out the old valve coil and install the new one. Just 5 minutes. I plugged in the dryer again, turned it on, and it worked.

Removed frontage of dryer removed plate covering bthe blower wheel. Removed clip holding the old blower wheel and inserted new one and replace clip, plate and front of dryer.

Replaced part according to instructions

I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be replaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.

First I opened the front of my dryer panel to see when the dryer was on if there was any gas flowing. I found that the ignitor was glowing , but no gas was releasing from the valve. So I figured that that is the root of the problem. I changed the old gas valves and replaced them with the new ones. It worked!! The whole process didn't take more than 30 minutes.

I watched the video and did the repair myself. My husband, who works in maintenance, was IMPRESSED! Yay! Thank You!!!! Love you guys! I am forwarding your website to my children!

i ordered a new filter and put in in the dryer to replace the broken one. everything worked out fine. and is working fine now.

At first I thought the sensor in the drum part was bad. It had some residue from something on it and looked a bit beat up. Replaced it for 30$ and had the same problem. Note: I decided to take the console panel off because I though it was necessary to get to everywhere else and I found a folded up "repairman trouble shooting guide" in the console. Don't know if this is a common place to put it but it had all the wiring and problems detailed with this dryer. It had step-by-step assessment procedures for any problem. However, I punched the sequence for the "brains" to give me a problem code and it indicated that I needed a new "user interface," a 285$ part. I must have punched it wrong because I started to read other problem descriptions and I realized, based on others, that the most likely cause was the coils that regulate the gas/heat valve. I used the "problem guide" to measure the resistance of the coils (it gives you the proper range for each) and one was outside of what it should have been so I purchased a new set of coils for $20 plus shipping. It took me 2 tries at installing the coils because the cover plate that seats the coils in place was not aligned properly the first time. This cause them to vibrate and rattle when starting up. The coils were a little different in height so I readjusted the cover bracket and seated the coils properly. No rattle and the dryer worked perfectly.

Need a short handled phillips screwdriver. Unplug dryer from socket. Remove two screws near the bottom of the front panel. Swing the panel to one side so electrical wire doesn't need disconnection. Remove two screws holding bracket over the two coils. Unplug both coils. Plug in new coils. Replace bracket. Replace front panel. Plug machine back into electrical socket. Problem solved.

Very easy

I have to admit I did not fix this. This dryer is at our beach house and my daughter and her family went down with part in tow. My son in law is an engineer and very smart and handy. He had the dryer purring like a kitten in no te with the part ordered. Thank you Lord and Will!!

followed u tube videos (several) did not find exact model. took dryer outside to disassemble and "clean out" with air hose and shop vac. Easily got it apart and replaced rollers,belt. to reassemble the idler unit was nearly impossible to reset as the motor and fan assembly is in FRONT very hard to see and get hands in. So, took my cut off wheel op grinder and "removed" the lower louvers on back. Viola simple as pie!

I got great advice and the know how form other's instructions. It was a really easy fix. I unplugged the dryer and turned off the gas valve. Open up the dryer by taking out the two screws securing the lint screen. Then pop off the top of the dryer by inserting a screwdriver. Disconnect the door switch and depending on model remove the two screws or bolts that keep the front panel attached. Careful, on my dryer once took the front panel off the drum fell forward. I kept it in place by wedging a small cardboard box under it. Unplug the two wires going into each of the coils. Remember which one goes where(2 prong vs 3 prong). Undue the two screws holding the bracket to the coils and remove bracket and bad coils. Put the new coils in, attach wires and bracket. Put dryer back together. Make sure to remember to plug back in door switch. I forgot and when I tried to test it wouldn't work and it got me worried that I broke it or something.

I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.