Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CYG4000AWW > Instructions

CYG4000AWW Magic Chef Dryer - Instructions

All installation instructions for CYG4000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CYG4000AWW
766-780 of 825
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not turning.....broken drive belt

  • Customer: Ashby's from Foster, WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

Flame would go out after start up. The Igniter would glow not light

  • Customer: Jay from South Bound Brook, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair itself was not hard, Pop top, unscrew front panel and pull forward to get at the coils under the drum. --THIS IS THE KEY POINT i ENCOUNTERED: I tested the coils and the resistance was right according to the schematic. But still the flame would go out after while. --on a whim I pulled the front cover and tested the coils immediately after the flam wouldn't re-light.---When the coil got warm, it would open (no continuity). When it cooled down again the correct continuity would return. Replaced the coil and no more problem

broken belt

  • Customer: Joy from livingston, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
It was really easy I watched your video on how to do it the video went step by step and was very helpful

Broken Belt

  • Customer: Jeffrey from Bensalem, PA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video you sent me, and every thing fell into place

Replace Drive Belt

  • Customer: William from Marlborough, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Broken lint filter

  • Customer: Katherine from Indianapolis, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Replacing the lint filter was, of course, the easy part. The rest of the time was spent removing the front of the dryer and cleaning out all the lint that had escaped through the old broken filter. I completely took apart the lint traps inside the front, vacuumed everything out, and replaced the ductwork to the outside that was almost completely blocked with lint. Please take the time to inspect your dryer, and do this if necessary! I feel we prevented a house fire by getting to this in time - and I will be more vigilant in the future.

Dryer quit heating.

  • Customer: John from La Crescenta, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws from front panel and lifted front panel away, Turned it to the left so I could keep the door switch connected. The dryer would heat when it was first started, but then the burner would go off and would not come back on. I ran the dryer with the front panel off and could see the igniter glow and light the burner, but after the burner cycled off, the igniter would come back on but the gas would not come back on. I could tell it wasn't the thermostat because the igniter would come on, so I knew it must be the gas valve, and therefore probably the coils. The instructions on the website said that the coils were frequently intermittent, so that seemed like the problem. I tried checking out the coil resistance with an ohmmeter to try to confirm that, but couldn't really tell anything that way. I ordered the replacement coils Tuesday night, selecting the cheapest shipping; they shipped on Wednesday, and were delivered on Thursday! Amazingly fast! Removed two screws from the clip that holds the coils in place, unplugged the old coils, swapped in the new coils, screwed the retaining clip back on. All done. Before I replaced the front panel, I watched to see that it operated correctly. I could see the burner cycle off, then after a bit, the igniter glowed, and then the gas came back on and lit, just like it should. Problem solved. Put the front panel back on, and that's all there was to it. Well, I did vacuum out some of the dust inside the cabinet while I had the cover off. Just out of curiosity, I checked the resistance of the new coils before I installed them to compare with the old ones. Couldn't see much difference.

Broken Belt

  • Customer: gary w from Saint Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

lint filter screen was starting to deteriorate

  • Customer: David from Oakland, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took out the old, put in the new

Excess squealing noise upon startup

  • Customer: Mark from Independence, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Raised upper portion of dryer using putty knife on clips just above dryer door. removed 2 screws on inside corner above dryer door, then completely removed the front panel. Lifter out dryer barrel to expose the inner workings. Removed the 2 rollers at back of unit...(be sure to apply some med. weight grease on roller shafts... I used axle grease). Also, had to replace the blower wheel, original was broken in half. With 1/4" nut driver(if I remember correctly) remove the 6-7 screws holding the front cover on the fan blower assy. Using pliers remove the spring clip on front of blower wheel shaft. Upon installing new blower fan you might have to align the new wheel on shaft with the flat keyway then using a 1/2" socket hold it on the front of the blower wheel and lightly tap the wheel in place till seated at the back of the shaft. I use to assume that the majority of the noise I was hearing was coming from the busted dryer. I did have underlying suspicions that there was another source of noise from within my domicile. Once the dryer was re-assembled and 'purring' just like new my suspicions were confirmed. I was able to verify that the source of the 'other' noise was from my wife. I miss my old dryer!

heat cycle runs once then does not come back on

  • Customer: john from garden city, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
follow Steve the repairman's instructions they were very good

Dryer would not maintain heat

  • Customer: Joe from Freehold, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I started with the process of elimination, based on the web site part failure percentage...so I started with the cycling thermostat and thermal fuse, without success. Next, I placed an order for the 'M' Series New Style Coil Kit Part # PS334310. Which, are located behind the lower front panel

Dryer was shutting off after just a few minutes and with only small amout of clothes in it.

  • Customer: Michael from Northlake, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I basically followed the instructions in the video provided. They were very clear and detailed. I love this website. This is the second repair on this dryer using PartSelect.com Runs like new and I saved a lot on labor costs.

Broken Dryer belt

  • Customer: Glenn from Waterford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I follow the instructions from the video sent to me with the email to tell me my new belt was shipped. Made the whole job go a easy as could be. Parts Select made fixing my dryer so simple and I also got the belt within 2 days. I recommend buying parts only from you! Glenn

broke

  • Customer: David from Gulfport, MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
by hand
All Instructions for the CYG4000AWW
766-780 of 825