Models > CYG3004AWW > Instructions

CYG3004AWW Magic Chef Dryer - Instructions

All installation instructions for CYG3004AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CYG3004AWW
16-30 of 741
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No power to the unit.

  • Customer: Kevin from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 35 of 37 people found this instruction helpful
Popped the two latches at the front of the machine inorder to raise the lid/cover. Found the part just above and behind the drum. Removed the screws, disconnected the wires and replaced the parts. I did have to remove the heating coils, but that was easy too. No wonder the Maytag repair man has nothing to do! Thank you Partselect.com. Not only did you ship the part to my house fast, but it was just as expensive if not cheaper than going out for it. Plus, I found instructions for the repair on your forums. Thanks again, you have a customer for life!

High noise when switched on. Broken blower wheel.

  • Customer: Alexander from Green Valley AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 34 of 39 people found this instruction helpful
Lift top off. Removed front door. Removed blower wheel cover. Replaced blower wheel. Cleaned and put back togther. Needed circlip pliers to remove circlip retaining blower wheel.

GAS FLAME WOULD DROP OUT

  • Customer: FRED from BRIELLE NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 38 of 52 people found this instruction helpful
first it was a process of alimination to find out why it was dropping out. after the problem was found it was just a matter of replacing the holding coil on the gas valve.
THANK YOU
FRED KENNEY SR

Extended drying time. Some but not enough heat. Burner would light for 15-18 seconds at first then shut off for 1-3 minutes then light for 3-6 seconds and repeat for the length of the cycle.

  • Customer: Matthew from Lake Worth FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 30 of 16 people found this instruction helpful
Determining the problem was the hardest part. With multiple parts (coils,thermostats...)possibly causing similar symptoms, I narrowed it down to the two coil valves.
Un plug the dryer. Remove two screws at the base of the front panel. Turn the front panel 180 degrees to avoid disconnecting the door switch. Gas valve with coils on top are on the right in front. Remove two screws in bracket holding coils, disconnect the wires, replace with new coils and reconnect wires. One coil has 2 terminals the other has 3 no chance of crossing the wires. I used an offset/right angle screw driver for one of the bracket screws due to close proximity to the drum. A stubby phillips head will work. You can check the burner operation with the front panel off as long as the door switch is still attached. Swing the front panel around and lift back into place securing with the two screws. Dryer works fine now.

Dryer belt snapped

  • Customer: J. from Oakdale NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 26 of 30 people found this instruction helpful
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.

Lost all power even the light.

  • Customer: Jeremiah from Laureldale PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 25 of 27 people found this instruction helpful
I removed the top and front panel. I first cleaned all the lint from the bottom of the lint trap which clogged the vent and caused the dryer to overheat. Then I replaced the high limit thermostat and thermal fuse. Bingo!! Worked good as new.

Dryer will not start

  • Customer: paul from PEACHTREE CITY GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 25 of 29 people found this instruction helpful
I replaced the timer asembly, still did not start.
I REPLACED THE HEATER SENSORS, TWO OF THEM,THAT DID
THE JOB.I suggest to check both heater sensors first, one I missed at the beginning is on the right side of the heating coil, kind of hidden.I believe that one was the problem.
I could have saved myself some money if I had found and checked that sensor first.

Dryer would run but never shut off

  • Customer: Raymond from Newark TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 26 of 35 people found this instruction helpful
I removed the cover plate than pulled off the knob to gain access to the two screws holding the timer assy. in..once they were removed i removed the wires one by one and installed them on the new timer.then reinstalled it put the cover on and was done

Drum stopped turning, fan continued to blow

  • Customer: Richard from Davie FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 21 of 22 people found this instruction helpful
Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, etc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.

Dryer would start and heat, but after 1st cycle the burner would not fire and a buzzing sound was coming from the gas valve solenoid area. Igniter and other functions worked fine.

  • Customer: David from Bedford IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 20 of 21 people found this instruction helpful
Removed front of dryer, unplugged each coil to determine where buzzing was coming from.....determined it was the boosting coil....ordered part and replaced. Dryer works great....we think it had be going bad over time because drying times have noticeable decreased.

My dryer only heats up at the beginning of cycle so my clothes will not dry.

  • Customer: Monique from Mission Viejo CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 19 of 19 people found this instruction helpful
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.

The dryer would start to heat then the heat would stop

  • Customer: Theodore from Riverside CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 18 of 10 people found this instruction helpful
I changed out the cycling thermostat and the high limit thermostat. Mainly because that was what my research indicated was the problem. I then found some more information online that indicated the gas solenoid valves were bad. I ordered them from you and replaced them. The problem was fixed.

In order to replace the valves you need to remove the top panel. Two screws at the top of the front door assembly hold it on. Remove the screws, lift up on the front panel door assembly and move it to the side. The drum will rest in place. In the lower left corner, under the drum, you will see the solenoids. Two screws attach a plate that holds down the solenoids. Take the hold down plate off, disconnect the control wires attached to the solenoids and lift out the solenoid/control valves. To assemble everything, work backwards to the start. Good Luck

Would not heat sometimes

  • Customer: Chris from Laguna Niguel CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 17 of 18 people found this instruction helpful
Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

OLD DRYER KNOB BROKE

  • Customer: Donald from Keystone Heights FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 21 of 30 people found this instruction helpful
WIFE WANTED A NEW DRYER AS IT WAS USELESS WITHOUT A KNOB AND TIRED OF USING PLYERS TO TURN IT.

WENT TO INTERNET, ENTERED DRYER KNOB, LEAD ME TO YOUR SITE AND ITEM WITHIN TWO MINUTES. ORDERED AND RECEIVED IN 2 DAYS. NO TOOLS NECESSARY, JUST PUSHED IT INTO PLACE.

SAVED THE COST OF A NEW DRYER.

Intermittent or no gas ignition, HSI ignightor working

  • Customer: Steven from Sauk Village IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 21 people found this instruction helpful
Removed front of gas dryer and cleaned all lint out. Checked HSI, and cleaned flame sensor. Split (3 terminal) gas coil terminals were intermittent. Read about 700 ohms across outer two terminals, but center terminal to either outer terminal was open (Infiniti on meter) 2 terminal coil measured about 550 ohms. 3 terminal coil should read about 700 ohms across outer terminals, and about 1.5K ohms center to outer terminals. Unscrewed index cover plate and replaced coil, 2 terminal coil was okay. Reassembled and finished 12 loads of laundry no problems at all.
All Instructions for the CYG3004AWW
16-30 of 741