CYE3004AKW Magic Chef Dryer - Instructions

My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake

Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.

The very first thing you want to do is Unplug the Dryer. I then took the two screws out that hold the lint screen to the top of the dryer. Then I used and old butter knife to pry the front top of the machine open. The top is held in place by two plastic clamps. Once I got the top loose I raise it up. Once I had it raised, I pulled up and out on the front panel where the dryer door is. I left the door switch connected and just put the panel off to the right. I then removed the old belt which was lying under the drum. The drum does drop slightly once you take the door off. This was one of the hardest part of the project for me as I did not have any help. This would be much easier if you just have one other person to hold the drum. Anyway, I then placed the new belt around the drum and used my left shoulder / arm to hold up the drum while feeding the belt in the slot on the tensioner and then over the dryer motor pulley. Make sure you don't twist the belt. I originally had a twist and when I hand turned the drum the belt came off the pulley and the tensioner. I had to rethread the belt through the slot on the pulley and then put the belt back on the dryer motor pulley. I then gave the drum a couple complete turns to make sure everything was staying in place. The tensioner on my dryer did not look like the instructions that came with the new belt. My belt tensioner is like a half circle and the belt just rides on it. I think if I had it to do over I would have purchased a new tensioner also. I feel that the belts constant motion against the tensioner probably causes it to wear out faster. Once I made sure evrything was staying on I replaced the front panel that has the door. You just slide the bottom into the slots while holding up on the drum so it lies on the felt padding around the door. Replace all screws and presto. Works like a new Dryer. Make sure you don't forget to plug it back in... Overall it's a pretty easy fix and much less expensive then a service call or purchasing a new Dryer.

Pushed in the Door Catch, and it was fixed.

Popped the left and right side clips that hold the top, took out left and right side screws that held front face on, disconnected the wire that went to the door, tilted the door to me and lifted up from tabs on bottom. The old belt was broke, so it was easy to get off. Put the new belt on the drum making sure that the rubber ribs were touching the drum then I put the belt on the tensioner pully and motor pully. I rotated the drum by hand at least 1 full revolution to make sure that the belt was on right and it wasn't twisted, then I put everything back together. Easy 10 minute job... Art

I watched the installation video. It was exactly as shown.

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Identified the rollers as the root cause of the drum not freely rotating. They also squeaked a little at the beginning of any cycle. I replaced the rear rollers and shafts using the parts from the roller replacement kit. Easy to do. The hardest parts was re-installing the belt.

looked up model on partselect and used the part by symptom section, chose the"will not start" symptom, based on that, the high limit kit seemed obvious, ordered part,received part in two days. watched repair video on this web site, followed the instructions, which were very clear, after unplugging the dryer, replaced both limit switches using nut driver, couldn't have been easier! I echo what other reviewers have said, you have customer for life! well thought out website providing excellent service to a person who wants to understand how things work and then fix it.

Ordered part ( door latch ) flowed instructions easily fixed same.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

instructions were clear and repair was easy

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history