Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Handle had stainless steel look but was wrapped in metallic plastic that melted from heat generated by the large gas burner on the stove top.
Removed door from microwave. Pried inside door trim off. Removed 4 small retaining screws then pried inner door section out revealing the 4 screws holding the handle in place. Removed those screws installed new handle using 4 original black screws. Reassembled door in reverse sequence from above. Attached door to microwave and admired my work.
removed two screws, set in place. done. The best parts was that your ordering and shipping was out of this world. Never thought I would get the Filter that fast. Thanks You made my day.
When door was opened, the microwave would turn on.
Looked on line and found a you tube that said to check the door micro switches (there are three of them. Found one of the switches had an actuator that was stuck down. I got the actuator working but problem was still present. Another you tube showed how to repair the contacts in the switch and that solved the problem. however the plastic piece that holds the switches was broken and would not hold the switches securely. Ordered that piece and a new switch. Remove the vent plate on top (one phillips) and the control panel (one phillips). The switch holder is held in place with 2 phillips and is a little tricky to get it out and undo the wires. Once out, it's just a matter of putting the switches into the new holder and reinstalling it. Google the model number and the problem and there's virtually a you tube to repair ANYTHING.
Microwave does not have power at all, though outlet has power
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
It is easy to repair the burnt out bulb if one has the correct bulb. Your website is very user friendly and your service is great. I was not able to replace the bulb at this time because our RV is at the repair shop for some other matters. I am sure the installation of the new bulb will go smoothly. Thanks for asking. Sharry Kiehl
Open microwave door and remove plastic cover running across top of the oven box by unscrewing 3 Phillips head screws above and behind plastic cover. (4th screw to the right is not related to this cover). DO NOT PULL COVER STRAIGHT OUT. Cover slides either right or left then pops out. Remove old filter and replace and reinstall cover. Filter lays at a 45 degree angle against metal tabs tilting toward you.
I was surprised to find that the turntable for my 10 year old GE Profile microwave/convection oven was not readily available at my local GE retailer. I ordered the part from this website hoping that my order would be filled. I received an immediate response from customer service and the part was on my front doorstep in under 1 week! I would order from this website again!
open microwave door remove 3 screws on top of microwave, slide top panel to the left and pull out top panel slide old filter out put in new one and reassemble
microwave fan will not shut off when door is closed.
Slide thin blade between black plastic cover and microwave door frame and pry up gently to release snap in tabs for the top. They are about 8 inches from each side of the door lengthwise. Same for bottom, except pry down. Next pry outward at each end with blade between the black plastic frame and door frame to release snap in tabs. Doing this may take a bit of jiggle work and be gentle, this frame is fragile. Next there are 5 small phillips screws behind this frame to be removed. 2 bottom 2 top and 1 by door handle. When screws are loosened keep phillips driver holding the screw in, then cup your hand under each screw and catch them when removing them to prevent screws hitting the floor and bouncing to lostville. Next use the thin blade to pry door outer shell from door frame partially. Insert blade between metal frame and plastic shell of door approx. 4 inches from end lengthwise and pry up to release snap in tabs. Repeat for bottom except pry down. The door may separate at handle end now; if not insert blade vertically at handle end about 3 inches from top between metal frame and plastic door shell and pry out and again about 3 inches lower. Use fingers to pry handle end of door apart far enough to see the spring holding the latch. Use fingers or small needlenose pliars to undo spring then slide up plastic latch and remove. Place old spring onto hook in the middle of the new latch, position new latch with latch arms with circles pointing downward back onto metal frame with upper and lower latch guides hooking into metal frame. Push latch down and reconnect spring to metal hook in door frame. Slide new latch up and down a little bit to ensure proper operation. Next squeeze metal frame and outer door shell together until you hear the snap ins snap close. Next put a small bit of wax on end of phillips driver to hold the small screws and reinstall them. Next insert the end of the black plastic frame towards the hinges first into the door then rest the black plastic frame lightly against the microwave door. Press against the top back corner about 4 inches from the hinges and squeeze together the door and the frame. It will make snap sound then repeat for bottom corner. Next squeeze together about 4 inches from handle end at top then bottom to hear snap sound. Finally squeeze the vertical part together behind the handle and make sure black plastic frame is flush with metal door frame and you are done. Again these parts are fragile so take your time.
Oven wouldn't sensor reheat & error code on display
I looked at the exploded pic on your web site to find the location of the sensor. Next I removed the cover by unscrewing 15 screws then swaped the sensor and re assembled! Works great! Fixing it my self I saved at least 150$ and did not have to wait all day for a repair man who probaly would not have the part on the first visit.
Turn table motor malfunctioning, noisy and intermittent.
My oven is installed above the counter making it a bit difficult to reach the screws closest to the wall. Instructions should note that both harnesses need to be disconnected and that there are two screws, not one holding the motor. This one issue made it frustrating since that screw is located towards the back away from your vision. This is when the flash light and a bit of contortions were required.
To get the microwave out to fix it, Appliance repair man had to dismantle surrounding Cabinetry. It then took him half an hour to replace part. Reassembly took another 45 minutes.
Very easy to replace. This replacement part is the perfect fit for my microwave since the original part has been discontinued. It does have the night light and bright light feature.