Models > CVGX2423W > Instructions

CVGX2423W Jenn-Air Cooktop - Instructions

All installation instructions for CVGX2423W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CVGX2423W
16-26 of 26
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the spark igniters would continue to spark after the burners were lit

  • Customer: Robert from White Rock NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Since the problem would only occur when the right front burner was on, I first replaced the ignitor, but the problem persisted. To replace the spark module I had to pull the range out of the nook it is in in the counter top. Then (after ensuring that the power was off) I removed the back cover. The spark module was easily located and removing two screws and disconnecting a few wires liberated it. The new one went in easily since it is the same part number and an exact match. Put the back on and check that the problem was solved. Done!

fan wouldn't turn off

  • Customer: Conrad from Roswell GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 1 people found this instruction helpful
Removed the part that didn't work and replaced it with the new one

would not light

  • Customer: ned from leland MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 5 people found this instruction helpful
remove two screws then unplug the wires put the wires back on the new one

Igniter switch was inop

  • Customer: Mark from Kingwood TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It took longer to figure out how to get the selector cover off than it did to replace the switch. Once I had access it was only about a 10-15 minute job to install and put it all back together and operative. Actually a very easy job to do.

Purchased a used stove top with no burner caps

  • Customer: Beatrice from San Bernardino CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Purchase the caps and received them within a reasonable short time and just put them right onto the burners. Easy/Breezy

Our old grease filter was molding

  • Customer: Kathy from Gurnee IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the old filter out and put a new one in. No tools no fuss no muss. Very easy.

Needed new grease filter

  • Customer: Judith from Lady Lake AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The old grease filter was removed and the entire downdraft was cleaned. The new filter was slipped in. It is so nice to have the old one out. I am so appreciative of finding this part. :-)

replacement filter for jenn-aire

  • Customer: Fred from Mount Sinai NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the filter fit because the scale in the photo allowed me to choose which one to buy!

Nasty, clogged, old grease filter

  • Customer: Kim from Cottontown TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)

Continuous clicking

  • Customer: Matthew from Marengo IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The aluminum threads on the post (part15) can get stripped very easily. If you cannot tighten down the flat nut the clicking will occur.

The fan switch on the Jenn-Air downdraft cooktop was bad and needed to be replaced

  • Customer: ALAN from Encinitas CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Be sure to unplug the unit first. Removing the screws to the control panel, disconnecting the wires, and replacing the switch is the easy part. The threads are plastic where the nut holds the switch in place, and it would not stay tight, but popped loose because of the plastic threads. I added some super glue to the threads and hand tightened. Replace control panel cover, re-plug into outlet.
All Instructions for the CVGX2423W
16-26 of 26