Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
freezer too cold and refrigerator not cold enough because fan not working
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place. Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled. The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Original evaporator fan (31 years old) was making a lot of worn bearing noise
Empty freezer; Remove shelves and ice trays; Unscrew and remove the rear vertical panel; Unscrew and remove fan housing; Unscrew and remove fan from fan housing; Fan blade slides off the motor shaft without tools. Reverse order to reassemble with new fan motor.
I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Two of the two leveling jacks of this old refrigerator were missing and had to be replaced.
I ordered four leveling jacks from this site for the refrigerator using a slightly different model number (my model was not listed). I assumed that the jacks all had the same shaft diameter and thread size. However, it turned out that the two front jacks had half-inch shaft diameters. It could be that originally there were rollers in front. The two rear jacks had quarter-inch shafts with "feet" for supporting them on the floor. So, I had to return the four jacks I had ordered and find another solution. I found two half-inch threaded bolts at the local hardware store that fit the front holes perfectly. I purchased 3.5 inch bolts to give me enough room to find the proper adjustment. I used wooden blocks and a crow bar to raise one side of the refrigerator high enough to screw in the leveling jacks. I used an adjustable crescent wrench to turn the bolts' hex heads until they were the proper height. I used the two original quarter-inch jacks in the rear holes and adjusted them to the proper height to level the refrigerator on the concrete floor where it is located. Then I removed the wooden blocks and tested to make sure the refrigerator did not wobble. I found that using the two bolts (no leveling jacks for the front holes could be found) for the front jacks proved to be the ideal solution. The job took me about thirty minutes, including the time it took to move the refrigerator into its final location and adjust the leveling jacks once more to create a solid stance so that the refrigerator did not wobble. While I had the refrigerator away from the wall, I removed the rear panel and cleaned the blades of the cooler fan and removed dust and dirt build up near the compressor with a vacuum cleaner. Then, I screwed the panel back into position, moved the refrigerator into its final place in a corner of the garage and made sure there was enough air space around it to allow for proper air circulation. This took me about twenty more minutes. I plugged it back in and listened to it come alive again. It is old but has never needed a repair and keeps everything cooled or frozen. I would suggest using threaded hex-head bolts in place of original leveling jacks if they cannot be obtained. Problem solved.