Models > CTB1925DRW > Instructions

CTB1925DRW Magic Chef Refrigerator - Instructions

All installation instructions for CTB1925DRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CTB1925DRW
481-495 of 511
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker leaking water dripping into the bin and freezing the dispensing unit

  • Customer: Richard from Port Orange FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the part number and an exact replacement was ordered. The old unit was removed and what I failed to note was that the water supply hose for the new unit entered from the side. Further examination showed a small "break-out" piece at the rear of the unit. but I still had to do something about the hole in the side. I used a piece of metal tape to close off that hole, trimmed it to size, and installed the unit. It was really an easy install after I figured out what to do about the hole. Evidently, this unit is mounted on the side of the freezer compartment in some models. Reading the reports of others was a big help.

Old ice maker worked irratically and finally quit for good.

  • Customer: Richard from Peoria AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video and advice from the many others on this site and only have a few additional comments. First, the decorative cover on the front of the old unit is held on with two plastic teeth on the top and bottom of the cover. This was not at all apparent and it took me awhile to figure it out. I used a sharp knife to pry up the top edge until the teeth lost their grip on the metal notches in the old unit. Second, don't try to pull the cables out of the front of the old unit before removing that cover. It is held in with a plastic snap that must be depressed after the cover is removed. The video does a good job explaining how to remove the old metal arm and attach it to the new unit so that it will recognize the ice level in the bucket. Finally, don't bother looking around the web site for a button that enables you to add to these comments. You'll be contacted by email in a week or two for that.

ice maker quit making ice

  • Customer: denton from grinnell IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

Ice maker had been leaking for several months and needed replaced

  • Customer: Joe from Leonard TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.

exchange of defective light rocker switch

  • Customer: Steve from River Edge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

The ice maker had been dripping and than stopped making ice. I worked with it and got it to work again for a few days and than the same problem occured.

  • Customer: Kathleen from Waller TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on line first. I shut off the power to the refreigerator. I took the one screw out on the bottom of the ice-maker and pushed up on the ice maker. Than I disconnected the power harness inside the refrigerator. I took it out and changed out the harness from the old one to the new one and also the bar that dumps the ice. I reconnectected the harness to the back of the refrigerator, made sure that the water spout lined up correctly. Pushed the ice maker down on the screws and reconnected the screw that I had removed. Waited about 1 hour and had ice cubes. This was an easy process after watching the video.

refridgerator was not cooling to the proper temps and finally would not cool at all

  • Customer: John from LAS CRUCES NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.

REPLACED REAR COVER ON REFRIG.

  • Customer: RUDOLPH from NORWALK CT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REPAIR WAS VERY EASY. REMOVED OLD COVER (6 SCREWS) . PLACED OLD COVER ON NEW COVER AND COUNTER SANK SCREW HOLES TO NEW COVER. INSTALLED NEW COVER. LESS THEN 15 MIN.

Ice maker was leaking water.

  • Customer: Curtis from Rock Rapids IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screw from bracket on bottom side of unit then loosened the two screws on top side. Lifted unit off the two upper screws unpluged wires took cover off and removed ice arm, reinstalled all on new unit and installed it back in freezer. Did this in less than 10 mns.

Ice Maker Not Working

  • Customer: Corey from Bridgeton MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This process actually took 3 tries to resolve. Read the entire article it may save you money.
Before each trial I shut off the water and unplugged the refrigerator.
Trial 1
I went to the website and chose the part that had the highest percentage of resolution (78%), which was the actual icemaker. I followed the direction that another person described in detail how to replace. It was easy but it wasn’t the solution. It took me 15 minutes to switch out using a screwdriver and a nut-driver. Turned on the water and plugged the refrigerator in. However, after doing so I still had no ice.
Trial 2
Next, I tried replacing the small water pump that pumps water up to the ice maker. The part is called
the “Double Outlet Water Valve”. Here again on the premise that it was the next highest percentage part to fix my problem. I replaced this part in about 15 minutes with an adjustable wrench and a knife. This time a turned on the refrigerator and water squirted out of the plastic hose that feeds into ice maker’s water feed tube. Still no ice.
Trial 3
The last part to replace was the water feed tube which is a vinyl tube that extends from the outside back of the refrigerator to the ice maker. I read that if water shoots out of the plastic hose that attaches to the “Water Feed Tube” is most likely frozen. So, I replace the “Water Feed Tube”. I disconnected the plastic hose in the back and took some pliers and pulled the “Water Feed Tube” out from the back. It was frozen solid. I cut the new “Water Feed Tube” to the same length and inserted it into the back of the refrigerator. I will most like not go in all the way until you guide it in to the icemaker from inside the freezer. I used some good clear silicone caulk around the outside of the “Water Feed Tube” and attached the plastic hose to it with a small clamp. I was done in about 15 minutes. I plugged in the refrigerator and I let the caulk fully dry for 24 hours. Then I turned on the water. Within the hour I had ice. Finally!
What I determined was the “Water Feed Tube” froze up and caused the “Double Outlet Water Valve” to fail. So, it was necessary to replace both but not the ice maker. What happens in the process of making ice is as the ice maker cycles it calls for water from the “Double Outlet Water Valve”. You should first check to see if the “Water Feed Tube” is frozen. Remove it, use a hair dryer to thaw it out. Reinsert it and re-clamp it to the plastic hose. If that doesn’t resolve your problem or you find that it wasn’t filled with ice, make sure the “Double Outlet Water Valve” is pumping water to the ice maker. If it is, then, replace the ice maker. If it isn’t, replace the “Double Outlet Water Valve”. In other words, don’t go on the percentages. Go on the cheapest.

Bottom freezer was making constant grinding noises, then stopped making ice altogether. I researched the Amanda site, read the customer feedback info and instructions to replace the ice maker. We've been fortunate to have had no ice maker issues for this Amana unit for ten years! The fridge and fre

  • Customer: Sharon from Mukilteo WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled out the fridge, emptied the freezer, followed the video, which was very helpful. I watched it three times.

ice maker had always leaked. We were not able to use it.

  • Customer: Mary Ann from Oostburg WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
After several repairmen and still leaking, I did my own diagnosis. I went to Partselect and got the part the NEXT DAY!! Followed directions from video on line and it took less than15 mins.! Now we have more ice than we need! Thanks Partselect!!!

Chunks of non stick coating coming off. Water leaking into ice collection container.

  • Customer: Chris from jackson GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1.Pull refrigerator out from wall and unplug. 2.Turn the water source off! 3.Remove one screw from bottom and loosen two screws at the top of the ice maker. 4.Pull ice maker down and unplug the power connector. It has 2 locking tabs so press to release the lock. The water tube will pull out on it's own.5. Remove the cable, front cover and clips from old unit and install on the replacement unit.6.Re-Install new ice maker in reverse order. Always a good idea to take pictures before you do changes in case you are not sure.

Ice maker was leaking water into ice container, causing ice jam of scroll

  • Customer: Jerry from Gautier MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Changing the ice maker was easy as per video instructions. I did not shut down power during replacement. The new unit started making ice within an hour or so, however, the next morning, liquids on the refrigerator top shelf were freezing up! I lowered the frig temp set point one number, but the top shelf continued to freeze. My son had had a similar experience, and he suggested turning power off to the unit for several minutes. I turned off the breaker for about 15 minutes, then back on. The top shelf freezing problem cleared up, and everything started working like it should!

The ice maker that came with the refig stopped working after 1 YR!

  • Customer: Darwin from Sioux Falls SD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
If you watch the video on PartsSelect that will give you a general idea of how to do the repair except mine was in a bottom drawer freezer. You have streach a little to get to the screws holding the ice maker to un-screw them just enough to lift the ice maker out.
All Instructions for the CTB1925DRW
481-495 of 511