CTB1832VRD01 Magic Chef Refrigerator - Instructions

I unpluged fridge then took the cap off the fan moter then took the three nuts off the fan then unplugged the three wires. And visaversa, ta! Ra! Fridge works just like new.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Switch off power at mains outlet. Pull off the front trim panel on the control box at top of the refrigerator compartment (it is just clipped into place). Behind are two screws which you remove. Remove the bulb and also two screws underneath and towards back of the control box. You can then pull down the control box. The defrost timer board is now visible and can easily be switched out (it comes with instructions how to do this). This job too no more than 20 minutes and saved me buying a new refrigerator at $1000.

Unplugged the refrigerator and then unloaded the freezer. removed the panel at the back of the freezer to expose the fan. Carefully unclipped the wiring harness and then removed the fan motor. Swapped the fan from the old motor to the new one (I did use a hair drier to warm the plastic fan to make it easier to remove) and reassembled the fan and panel. Simple and easy, and now the refrigerator works just like new.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

After removing two rear plastic panels, (very easy). The fan is easily accessable. Two more screws to remove the fan brace and remove three wires from the fan and its out. Reverse the process and its finished. The propellor is not part of the fan motor order and you can remove the old propellor and put on new motor (easy). One step that is not accounted for is the removal of a flexable plastic "nut" on the fan shaft. This piece holds and connects the fan to the fan brace. You will understand this when you compare the new fan with the old and see the plastic "nut" sleeve on the old fan. Simply pull it off and put on new motor shaft (it simply slides on and off the shaft).

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...

Looked at your You Tube video and followed the instruction

much like yout video. However I got the mounting bracket upside down and had to do the job twice. When finished it worked perfectly. Great! However in Missouri outside temperature was over 100 and refrig was in shed. My beer got warm. Thank you.

Just followed the video that you guys had on line . It was a very easy repair

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

repair went well. Ice maker still not making ice. UGH