Models > CTB1723ARA

CTB1723ARA Magic Chef Refrigerator - Overview

Get Parts and Repair Help for CTB1723ARA

If you know the refrigerator repair part you need, you can browse the list of all parts on the CTB1723ARA, or you can search by name or part description. You can also find your part by where it is located on the CTB1723ARA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for CTB1723ARA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$107.31

Ice Maker

This replacement ice maker mechanism does NOT come with a cover, a wire harness, or the mounting hardware. Must be ordered separately.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$2.70

Screw

Sold individually.

$8.27

Shelf Retainer Bar End Cap

Sold individually.

$3.76

Crisper Drawer Shelf Support

This crisper drawer shelf support is used for many refrigerators.

$2.70

Screw

This screw is sold individually.

$7.87

Light Rocker Switch

$15.05

Water Fill Cup and Bearing

$38.66

Single Outlet Water Valve

This valve has a 1/4" tubing inlet connection. When energized, this part releases water from the supply line into the ice mold.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 502 of 511 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 202 of 273 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 88 of 91 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more