CSX22GRSBWH Hotpoint Refrigerator - Instructions

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.

turned water off removed old water valve moved wires to new one moved water supply and discharges to new one reinstalled new valve

Followed easy video instructions. Loosened the necessary bolts, etc. Replaced hinge assembly, lined up door, lubed the hinge with vasoline. Works perfectly now. May purchase another assembly as spare as it appears this may be a common repair issue.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

I used the how to video from the site and had the part replaced in about the same time the video did it, even with being distracted with a phone call.

did it just as the video showed. it was a little different, but absolutely nothing that we as ametures could not figure out! very easy and I think it was just the part we needed! biggest thing was unloading refrigerator!

I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.

I have never repaired anything before but I found your web site ordered the item and received it in 2 days Thank You,thank you

I watched the "How To" video on the Parts Select web site twice. The video was very helpful, kind of like having someone right there with you showing you how to replace the hinge. I emptyed the door shelves, removed the top hinge hexscrews and easily lifted the door off the lower hinge, pieces of the broken cam hinge on the door fell off. I set the door on the floor in front of the sink with the handle edge on the floor. I unbolted the hinge and installed the new one. I loosened one screw on the door cam hinge and removed the other, easily replacing the broken part. Before tightening the screws I checked to make sure the hinge hole in the door was not blocked by the new cam hinge. I lifted the door and water ran out from somewhere. I tried to set the door on the lower hinge several times with no luck. I rechecked the hole, it was still clear. I tried placing the door on the refrigerator using the seal to hold it in place, that worked but I couldn't get the door to drop down onto the hinge. I played with it some more and finally got it in place, reinstalled the top hinge, mopped up the water and tried the door. It didn't self close. I adjusted the top hinge a couple of times and applied a little silicone to the hinges, it still didn't self close. I told my wife to make sure the door closes completely and reloaded the stuff into door. After a couple of days it now closes by itself like it's supposed to. In retrospect, I was alone doing the replacement and it really was an easy job but a second person to help line up the lower hinge would have helped a lot.

I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.

I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.

I watched the repair video. Replaced the cam on the bottom of the door and the hinge pin. Now the door closes on its own, just like brand new.