CSK25GRYAAA Hotpoint Refrigerator - Instructions

The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!

replace the lower door hinge assy. and closer cam as a set.Only used a 1/4" socket and ratchet.The process was very easy without any problems.

I am clueless around the house. But this was easy: Removed ice maker bin, fiddled with freezer shield to line up with the single screw hole that holds it in place. Use screwdriver to install shield with original screw that stayed in place after the original freezer mount cracked and broke. Put ice maker bin back. Done!

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.

Part came in on time, and the repair went smoothly - no problems

I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.

I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!

Followed easy video instructions. Loosened the necessary bolts, etc. Replaced hinge assembly, lined up door, lubed the hinge with vasoline. Works perfectly now. May purchase another assembly as spare as it appears this may be a common repair issue.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Removed the old broken one with screw driver and installed new one with screw driver and voila all done!

I watched the "How To" video on the Parts Select web site twice. The video was very helpful, kind of like having someone right there with you showing you how to replace the hinge. I emptyed the door shelves, removed the top hinge hexscrews and easily lifted the door off the lower hinge, pieces of the broken cam hinge on the door fell off. I set the door on the floor in front of the sink with the handle edge on the floor. I unbolted the hinge and installed the new one. I loosened one screw on the door cam hinge and removed the other, easily replacing the broken part. Before tightening the screws I checked to make sure the hinge hole in the door was not blocked by the new cam hinge. I lifted the door and water ran out from somewhere. I tried to set the door on the lower hinge several times with no luck. I rechecked the hole, it was still clear. I tried placing the door on the refrigerator using the seal to hold it in place, that worked but I couldn't get the door to drop down onto the hinge. I played with it some more and finally got it in place, reinstalled the top hinge, mopped up the water and tried the door. It didn't self close. I adjusted the top hinge a couple of times and applied a little silicone to the hinges, it still didn't self close. I told my wife to make sure the door closes completely and reloaded the stuff into door. After a couple of days it now closes by itself like it's supposed to. In retrospect, I was alone doing the replacement and it really was an easy job but a second person to help line up the lower hinge would have helped a lot.

I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.

I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.

I watched the repair video. Replaced the cam on the bottom of the door and the hinge pin. Now the door closes on its own, just like brand new.