CSF22MTC Hotpoint Refrigerator - Instructions

Connected the 2 wires and pushed in the switch until it clicked.

per your instructions

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

I removed the back of the refrigerator access panel disconnecte the 3 bolst holding the motor to the fan shroud assembly and removed the burned wires from the recepticle end at the wring harness. The fan motor comes with wire nuts but I chose to use the same style of connector as came with the OEM motor. I purchased the new connectors from NAPA and they are an exact fit. The new motor fit perfectly and has run flawlessly since the installation. It is in an awkward location and that takes time to get yourself into position but once there the assembly is very simple and it is rewarding to be able to use the appliance again. The ordering from the website and phone order are very easy to do and you have what you need in a timely and expeditious manner.

Noticed the fan was not working properly and went online and found out that was the cause. I immediately ordered the part that night at 8:21pm and received the motor and fan blade the next day. I flipped the refrigerator on its side and removed the 3 hex bolts, took off the fan blade first and removed the wires from the motor. I put in the new motor and then added on the new blade and put the 3 hex bolts back on and the wires. The whole process took about 30 minutes. Piece of cake.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

pull refrig.from wall. Remove water lines and unplug elect.wires from valve. Remove the one screw that attached the valve to refrig.. To install new valve reverse procedure. push refrig. back into position. This was so easy.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.